Ogółem głosów: 416
Musisz zalogować się, aby móc zagłosować. Rozpoczęto: 02/02/2015 09:38
Twoje IP
3.133.144.197
Linksys Beta Firmware
Do działu Download trafiły cztery beta firmware linksysa, dla sprzętu z serii RVxxx : RV016 fw v2.0.12, RV0041 fw v1.3.6, RV042_1.3.7.8, RV082 fw 1.3.3.4.
Beta Firmware for the RV042 v1.3.7.8
New Features:
1. Support Paid Custom DNS for dyndns.org. A Custom DNS checkbox is displayed on Setup->DDNS->DynDNS.org page.
2. Support IPSec NAT Traversal in both Gateway-to-gateway
Issues Fixed:
1. Fix the "Selective Acks Off" issue that affects performance.
2. Fix the issue with saving a pre-shared key with apostrophe.
3. Fix the subnet mask issue. Remark: In previous firmware, when the router's subnet mask is set to 255.255.255.192, 255.255.255.224, 255.255.255.240, 255.255.255.248, or 255.255.255.252, you will no longer be able to change the subnet back to 255.255.255.0.
4. Restrict the Dynamic IP Range in DHCP Server Configuration to be in accordance with the LAN IP and Subnet Mask configuration of RV router. For Example, when LAN IP/Mask = 192.168.1.1/255.255.255.128, the DHCP IP Range the user can configure will be restricted to the range of 192.168.1.1 through 192.168.1.126.
5. Fixed a PPTP Server problem that failed to establish PPTP connection when DMZ Host enabled.
6. Disallow users to set x.x.x.0 in the LAN IP address field.
7. Update the on-line help of VPN Client Access (QuickVPN) Setting.
8. Modified the alert message as the following when enabling Remote Management.
(1) When https is enabled, remote management enabled, and password being the default password,
Message: The Router is currently set to its default password. As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
(2) When https is disabled, remote management enabled, and password being the default password,
Message: Please be warned that once remote management is enabled, it will be safer to remotely administer the router by https on port 443 instead of http. The Router is currently set to its default password.
As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
9. RV042 will listen to ports 443 and 60443 for QuickVPN connection. Remark: Earlier firmware only listens to port 443.
RV082 Firmware v1.3.3.4 Release Note
There are two firmware systems used by RV082. One is firmware v1.3.x which uses the newer Intel CSR1.2.2. The other is firmware v1.1.x which uses the original Intel CSR1.1. The look and feeling are quite similar, however, the v1.3.x firmware provides more features and better performance than v1.1.x. For example, the NAT firewall throughput has reached 200Mbps (bi-directional wire speed) and the IPSec throughput (3DES) has a maximum over 90Mbps. You can upgrade or downgrade the firmware on your RV082 device whenever you want. But like before, downgrading firmware will restore the configuration settings to factory default.
New Features:
1. Support Bandwidth Management, a feature already exists in RV016. Note: Since a new tab "Bandwidth Management" is inserted to the menu bar, the tabs "Restart" and "Setting Backup" are pushed to the "More… >>" page.
2. Support NAT-Traversal on both Gateway-to-Gateway and Client-to-Gateway modes.
3. Support Custom DNS, a paid service provided by dyndns.org. A Custom DNS checkbox is added on the Setup -> DDNS -> DynDNS.org page.
4. RV082 will listen to port 443 and port 60443 for QuickVPN connection. Remark: The earlier firmware listens to port 443 only.
5. Support SNMP Cold-start, Warm-start, Link-up and Link-down traps.
6. Change the DHCP Server implementation. When the DHCP client requests the IP address of DNS server, RV082 will offer the DNS server address obtained from ISP. (In previous firmware, RV082 offers the DNS server address as RV082’s LAN IP.)
Fixes:
1. Add "linksys.com" as the default Domain Name and leave Host Name to be blank after a reset to Factory Default.
2. Restrict the Dynamic IP Range in DHCP Server Configuration to be in accordance with the LAN IP and Subnet Mask of RV082.
For Example, when LAN IP/Mask = 192.168.1.1/255.255.255.128, the DHCP IP Range user can configure will be restricted in the range of 192.168.1.1 through 192.168.1.126.
3. Fixed a PPTP Server problem that failed to establish PPTP connection when DMZ Host was enabled.
4. Fixed an issue with saving a pre-shared key with an apostrophe.
5. Disallow user to configure RV082’s LAN IP address to be a broadcast IP address (x.x.x.0.)
6. Add an alert message if user configure “Send SNMP Trap to:__” as a non-IP address.
7. Modified the alert message when Remote Management is enabled.
(1) When https enabled, remote management enabled, and password = admin, the pop-up message will read:
The Router is currently set to its default password. As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
(2) When https disabled, remote management enabled, and password = admin, the pop-up message will read:
Please be warned that once remote management is enabled, it will be more secure to remotely administer the router via https via port 443 instead of http. The Router is currently set to its default password. As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
8. Update the on-line help of VPN Client Access (Quick VPN) to explain the two versions of firmware of RV082. The default version supports 15 QuickVPN clients, whereas the q50 version supports 50 clients.
9. Fix the subnet mask issue. Remark: When the router’s subnet mask has been set to 255.255.255.192, you will no longer be able to change the subnet back to 255.255.255.0. For example, suppose you change the subnet mask from 255.255.255.0 to 255.255.192 and save the settings. You then want to change the subnet mask back to 255.255.255.0. You select it from the Subnet Mask drop-down box. Every time you click the Save Settings button, error “DHCP IP Address Range conflict with the LAN IP” will appear, and it will not allow you to change it.
RV016 Firmware v2.0.12 Release Note
New Features:
1. Support Custom DNS, a paid service provided by dyndns.org. A Custom DNS checkbox is added to the Setup->DDNS->DynDNS.org page.
2. Support IPSec NAT-Traversal in both Gateway-to-gateway and Client-to-gateway modes.
3. RV016 will listen to ports 443 and 60443 for QuickVPN connection. Remark: Earlier firmware listens to port 443 only.
Issues Fixed:
1. Fix the "Selective Acks Off" issue that affects performance.
2. Fix the issue with saving a pre-shared key with apostrophe.
3. Fix the subnet mask issue. Remark: In previous firmware, when the router's subnet mask is set to 255.255.255.192, 255.255.255.224, 255.255.255.240, 255.255.255.248, or 255.255.255.252, you will no longer be able to change the subnet back to 255.255.255.0.
4. Restrict the Dynamic IP Range in DHCP Server Configuration to be in accordance with the LAN IP and Subnet Mask configuration of RV router. For Example, when LAN IP/Mask = 192.168.1.1/255.255.255.128, the DHCP IP Range the user can configure will be restricted to the range of 192.168.1.1 through 192.168.1.126.
5. Fix a PPTP Server problem that failed to establish PPTP connection when DMZ Host enabled.
6. Disallow users to set x.x.x.0 in the LAN IP address field.
7. Fix an issue with enabling IPCompress (IPComp).
8. Update the on-line help of VPN Client Access (Quick VPN) to explain the two versions of firmware of RV016. The default version supports 15 QuickVPN clients; the q50 version supports 50 clients.
9. Add "linksys.com" as the default Domain Name and leave Host Name to be blank after reset to factory default.
RV0041 Firmware v1.3.6 Release Note
1. Support IPSec NAT-Traversal in both Gateway-to-gateway and Client-to-gateway modes.
2. Support Custom DNS, a paid service provided by dyndns.org. A Custom DNS checkbox is added on the Setup -> DDNS -> DynDNS.org page.
3. RV0041 will listen on ports 443 and 60443 for QuickVPN (VPN Client Access) connection request.
4. Both IP address and domain name are supported in the "SNMP Trap Sent to:" field.
5. Fixed an issue with saving a VPN pre-shared key with an apostrophe.
6. Fix the subnet mask issue. Remark: When the router’s subnet mask has been set to 255.255.255.192, you will no longer be able to change the subnet back to 255.255.255.0. For example, suppose you change the subnet mask from 255.255.255.0 to 255.255.192 and save the settings. You then want to change the subnet mask back to 255.255.255.0. You select it from the Subnet Mask drop-down box. Every time you click the Save Settings button, error "DHCP IP Address Range conflict with the LAN IP" will appear, and it will not allow you to change it.
7. Disallow user to set x.x.x.0 as the LAN IP address.
8. Modified the alert message when Remote Management is enabled.
(1) When https enabled, remote management enabled, and password = admin, the pop-up message will read:
The Router is currently set to its default password. As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
(2) When https disabled, remote management enabled, and password = admin, the pop-up message will read:
Please be warned that once remote management is enabled, it will be more secure to remotely administer the router via https on port 443 instead of http. The Router is currently set to its default password. As a security measure, you must change the password before the Remote Management feature can be enabled. Press "OK" to change your password, or press "Cancel" to leave the Remote Management feature disabled.
· Łącznie użytkowników: 24,117 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
tamtosiamto
31-03-2024 12:54
Wesolego jajka wszytskim forumowiczom
tamtosiamto
28-03-2024 23:24
tak, tak zgadza sie, ale ja pytam o wykluczenie noda na guest network w first set, i to nie dziala
Adooni
24-03-2024 13:16
Guest network is currently designed to allow the first set of each band (2.4G, 5G, 5G-1) available to the AiMesh node
tamtosiamto
24-03-2024 03:03
ale w 1 jest opcja do wyboru - dla calej sieci albo rutera only i wlasnie o tym mowie, ze nie dziala
Adooni
23-03-2024 16:31
w dokumencie asusa jest ze wlasnie dla 1 ma dzialac na nodach tez
tamtosiamto
23-03-2024 15:39
tak, ale nie zmienia to faktu, ze w pierwszej nie dziala wylaczanie aimesh dla goscinnej( a powinno), czyli jest jakis bug. Mam start soft, bo to dsl-ac68 ktory nie jest juz updateowany
Adooni
22-03-2024 18:07
nie, 1 wsza bedzie wszedzie trzeba 2ga zrobic dla kazdego pasma te nie sa przenoszone
tamtosiamto
19-03-2024 19:57
czyli jak mam jedna siec goscinna to powinno dzialac separowanie gosci od noda -a nie dziala
tamtosiamto
19-03-2024 19:50
@Adooni 'Only one set is available for 1 band' i tak mam-1 set dla 2.4ghz i 1 dla 5ghz-czy czegos nie rozumiemW drugiej sieci goscinnej nie ma opcji wyboru Ruter only/ All nodes
Adooni
19-03-2024 19:14
no to przeczytaj to 2 pod - 1 stet z kazdego pasma jest dopuszczony na nody. zrob 2 siec jako goscinna na danym pasmie i wtedy sprawdz
' target='_blank'>Link
