drukarka drukuje tylko raz
|
zakk87 |
Dodano 22-04-2023 12:56
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
ponawiam temat wydruków w FT 2023.2. Do tej pory działało wszystko dobrze ze smartfonów czy komputerów.
W tym momencie po restarcie routera mogę wydrukować tylko raz lub w krótkim czasie po restarcie.
Na bitbucket ni mogę otworzyć problemu.
Cytat Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: ------------[ cut here ]------------
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: WARNING: at fs/proc/generic.c:588 proc_register+0xec/0x1bc()
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: proc_dir_entry '/proc/usblp' already registered
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: tntfs bf863000 439769
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: exfat bf843000 97983
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: vfat bf83b000 8509
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: fat bf82a000 43022
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ext4 bf7e9000 221882
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: crc16 bf7e3000 1007
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: jbd2 bf7d0000 48989
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: mbcache bf7c9000 4599
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: usb_storage bf7ba000 34290
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: sd_mod bf7ae000 21995
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: scsi_wait_scan bf7a8000 416
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: scsi_mod bf783000 108730
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nls_cp852 bf77d000 3706
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ehci_hcd bf76f000 32414
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: tun bf72a000 11522
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ebtable_filter bf6ee000 1127
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ebtables bf6e5000 15587
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: usblp bf5a8000 10329
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ip6table_mangle bf548000 1059
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ip6table_filter bf542000 895
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ipt_account bf53a000 8376
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: xt_recent bf52d000 7136
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ipt_REDIRECT bf520000 826
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: xt_DSCP bf51a000 1474
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: wl bf0d1000 4208125
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: dpsta bf0c7000 14556
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: usbcore bf095000 103389
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: jffs2 bf077000 91266
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: zlib_deflate bf06d000 19757
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_nat_pptp bf067000 1598
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_conntrack_pptp bf061000 3363
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_nat_proto_gre bf05b000 887
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_conntrack_proto_gre bf055000 3320
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_nat_ftp bf04f000 1144
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_conntrack_ftp bf048000 4909
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_nat_h323 bf041000 4761
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: nf_conntrack_h323 bf033000 33807
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: et bf01c000 65158
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: igs bf014000 11927
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: emf bf00b000 15397
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: module: ctf bf000000 21199
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: Modules linked in: tntfs(P) exfat vfat fat ext4 crc16 jbd2 mbcache usb_storage sd_mod scsi_wait_scan scsi_mod nls_cp852 ehci_hcd tun ebtable_filter ebtables usblp ip6table_mangle ip6table_filter ipt_account xt_recent ipt_REDIRECT xt_DSCP wl(P) dpsta(P) usbcore jffs2 zlib_deflate nf_nat_pptp nf_conntrack_pptp nf_nat_proto_gre nf_conntrack_proto_gre nf_nat_ftp nf_conntrack_ftp nf_nat_h323 nf_conntrack_h323 et(P) igs(P) emf(P) ctf(P) [last unloaded: nls_cp852]
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0042000>] (unwind_backtrace+0x0/0xf8) from [<c0060900>] (warn_slowpath_common+0x4c/0x64)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0060900>] (warn_slowpath_common+0x4c/0x64) from [<c00609ac>] (warn_slowpath_fmt+0x30/0x40)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c00609ac>] (warn_slowpath_fmt+0x30/0x40) from [<c010eeb4>] (proc_register+0xec/0x1bc)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c010eeb4>] (proc_register+0xec/0x1bc) from [<c010f248>] (proc_mkdir_mode+0x3c/0x60)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c010f248>] (proc_mkdir_mode+0x3c/0x60) from [<bf5a9a60>] (usblp_probe+0x3c4/0x648 [usblp])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf5a9a60>] (usblp_probe+0x3c4/0x648 [usblp]) from [<bf09f218>] (usb_probe_interface+0xcc/0x130 [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf09f218>] (usb_probe_interface+0xcc/0x130 [usbcore]) from [<c0192af8>] (driver_probe_device+0x78/0x174)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0192af8>] (driver_probe_device+0x78/0x174) from [<c0191a8c>] (bus_for_each_drv+0x60/0x8c)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0191a8c>] (bus_for_each_drv+0x60/0x8c) from [<c01929ac>] (device_attach+0x70/0x88)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01929ac>] (device_attach+0x70/0x88) from [<c01922f8>] (bus_probe_device+0x24/0x40)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01922f8>] (bus_probe_device+0x24/0x40) from [<c01904a4>] (device_add+0x44c/0x5b0)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01904a4>] (device_add+0x44c/0x5b0) from [<bf09e3a4>] (usb_set_configuration+0x3fc/0x5ec [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf09e3a4>] (usb_set_configuration+0x3fc/0x5ec [usbcore]) from [<bf0a4bd4>] (generic_probe+0x44/0x94 [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf0a4bd4>] (generic_probe+0x44/0x94 [usbcore]) from [<bf09e62c>] (usb_probe_device+0x14/0x18 [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf09e62c>] (usb_probe_device+0x14/0x18 [usbcore]) from [<c0192af8>] (driver_probe_device+0x78/0x174)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0192af8>] (driver_probe_device+0x78/0x174) from [<c0191a8c>] (bus_for_each_drv+0x60/0x8c)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c0191a8c>] (bus_for_each_drv+0x60/0x8c) from [<c01929ac>] (device_attach+0x70/0x88)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01929ac>] (device_attach+0x70/0x88) from [<c01922f8>] (bus_probe_device+0x24/0x40)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01922f8>] (bus_probe_device+0x24/0x40) from [<c01904a4>] (device_add+0x44c/0x5b0)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c01904a4>] (device_add+0x44c/0x5b0) from [<bf098368>] (usb_new_device+0x68/0xb0 [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf098368>] (usb_new_device+0x68/0xb0 [usbcore]) from [<bf098a0c>] (hub_thread+0x65c/0xf28 [usbcore])
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<bf098a0c>] (hub_thread+0x65c/0xf28 [usbcore]) from [<c00790c4>] (kthread+0x88/0x90)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: [<c00790c4>] (kthread+0x88/0x90) from [<c003cb8c>] (kernel_thread_exit+0x0/0x8)
Apr 22 12:53:19 RT-AC66UB1 kern.warn kernel: ---[ end trace c6a65a7f7c951c30 ]---
Edytowany przez zakk87 dnia 22-04-2023 13:10
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
pedro |
Dodano 25-04-2023 14:07
|

Moderator

Posty: 1012
Dołączył: 21/09/2015 15:03
|
To żeby wszystko było w jednym miejscu:
- router to RT-AC66U_B1?
- jaka to drukarka?
- mam rozumieć że drukarka podpięta po USB i "USB Printer Support" załączony? A "Bidirectional copying"?
- a jak z pozostałymi modułami:?
USB 3.0 Support
USB 2.0 Support
USB 1.1 Support
OHCI
UHCI ?
- na jakiej ostatniej wersji FT wszystko było w porządku?
|
|
|
|
zakk87 |
Dodano 25-04-2023 14:45
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
router: AC66U_B1
drukarka: HP LJ 1022
USB Printer support włączony, bidirectional wyłączony
USB 3.0 Support [ ]
USB 2.0 Support [*]
USB 1.1. Support [ ]
OHCI [ ]
UHCI [ ]
ostatnia wersja gdzie drukowanie działało w każdej chwili to 2022.6 lub 2022.7 ? Z tego co pamiętam 2023.1 miałem krótko aczkolwiek zdarzyło się czasem coś wydrukować. Obecnie nie da się ani z PC ani z telefonu.
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
pedro |
Dodano 25-04-2023 16:46
|

Moderator

Posty: 1012
Dołączył: 21/09/2015 15:03
|
A jest dużym problemem zrobić downgrade do 2022.7 i sprawdzić (ale nieco dłużej) czy wszystko gra?
Nie trzeba ruszać nvram.
Jeśli nie używasz Routing Policy w kliencie OpenVPN, to będzie wszystko OK.
|
|
|
|
zakk87 |
Dodano 25-04-2023 18:33
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
Ok. Będę w domu to popróbuję. Dzieki
Scalony z 26 kwietnia 2023 14:22:39:
wróciłem do 2022.7 2 wydruki poszły.
Cytat Apr 26 14:15:45 RT-AC66UB1 lpr.notice p9100d[825]: Connection from ::ffff:10.0.0.15 port 2964 accepted
Apr 26 14:15:45 RT-AC66UB1 lpr.err p9100d[825]: read: Connection reset by peer
Apr 26 14:15:45 RT-AC66UB1 lpr.notice p9100d[825]: Finished job: 708/708 bytes sent to printer
Apr 26 14:15:45 RT-AC66UB1 lpr.err p9100d[825]: copy_stream: Connection reset by peer
Apr 26 14:16:12 RT-AC66UB1 lpr.notice p9100d[825]: Connection from ::ffff:10.0.0.15 port 2965 accepted
Apr 26 14:16:12 RT-AC66UB1 lpr.err p9100d[825]: read: Connection reset by peer
Apr 26 14:16:12 RT-AC66UB1 lpr.notice p9100d[825]: Finished job: 716/716 bytes sent to printer
Apr 26 14:16:12 RT-AC66UB1 lpr.err p9100d[825]: copy_stream: Connection reset by peer
zobaczę po południu i w kolejnych dniach czy będzie drukować. Jeżeli tak to zainstaluję 2023.1 i potestuję kilka dni ponownie.
Scalony z 28 kwietnia 2023 09:12:43:
teraz sprawa wygląda tak:
26 kwietnia poszły wydruki jak widać.
wczoraj nie mogłem nic wydrukować, nie pojawia się nic w dzienniku. Drukarka jest podpięta, gotowa do druku. Nie ma teraz błędów z pierwszego posta.
Wygląda na to, że po restarcie można wydrukować, w nocy coś się wydarza i później nie można już nic wydrukować. Z poprzednią drukarką 1018 było to samo już kilka lat temu. Musiałem ją restartować co jakiś czas lub odpinać. Nie mogę teraz znaleźć swoich postów ale coś było na rzeczy i specjalnie podmieniłem drukarkę na inną.
Scalony z 28 kwietnia 2023 09:57:04:
problemy już miałem na hp 1020 host based w sofcie 2022.1?
https://openlinksys.info/forum/viewthread.php?thread_id=22134&pid=178417#post_178417
Scalony z 29 kwietnia 2023 12:45:20:
2022.7 Uptime 2 dni. Wczoraj jak pisałem drukarka nie drukowała już więc wylaczylem na chwilę USB teraz wydruk wyszedł. Na 2023.2 już byłby reboot tomato albo error jak w pierwszym poście. Jest coś skopane z usb. Instalować 2023.1?
Scalony z 02 maja 2023 16:52:18:
uptime 6 dni, dziś drukarka wydrukowała.
Wgrywam 2023.1
Edytowany przez zakk87 dnia 02-05-2023 16:52
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
pedro |
Dodano 02-05-2023 17:34
|

Moderator

Posty: 1012
Dołączył: 21/09/2015 15:03
|
OK
|
|
|
|
zakk87 |
Dodano 06-05-2023 09:59
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
obecnie 2023.1, uptime 3 dni
w tym momencie chcę wydrukować, na PC wyskakuje tylko błąd druku a na routerze pusto w logach (zapewne muszę wyłączyć na chwilę obsługę drukarki albo odpiąć drukarkę)
ostatni wydruk
Cytat May 3 11:45:36 lpr notice p9100d[779] Connection from ::ffff:10.0.0.241 port 40888 accepted
May 3 12:00:22 lpr notice p9100d[779] Finished job: 9/9 bytes sent to printer
May 3 12:00:22 lpr notice p9100d[779] Connection from ::ffff:10.0.0.241 port 40892 accepted
May 3 12:00:25 lpr notice p9100d[779] Finished job: 330144/330144 bytes sent to printer
May 3 12:00:25 lpr notice p9100d[779] Connection from ::ffff:10.0.0.15 port 6605 accepted
May 3 12:00:25 lpr err p9100d[779] read: Connection reset by peer
May 3 12:00:25 lpr notice p9100d[779] Finished job: 23964/23964 bytes sent to printer
May 3 12:00:25 lpr err p9100d[779] copy_stream: Connection reset by peer
May 3 17:14:34 lpr notice p9100d[779] Connection from ::ffff:10.0.0.16 port 49668 accepted
i od tamtej pory cisza w logach. Czyli połączenie zostało otwarte ale wydruk nie przyjęty i tak wisi.
Scalony z 06 maja 2023 10:22:57:
po wyłączeniu obsługi drukarek
Cytat May 6 10:19:57 RT-AC66UB1 kern.info kernel: usbcore: deregistering interface driver usblp
May 6 10:19:57 RT-AC66UB1 kern.info kernel: usblp0: removed
May 6 10:19:59 RT-AC66UB1 user.debug wsdd2[1574]: 'Terminated' signal received.
May 6 10:19:59 RT-AC66UB1 user.info wsdd2[1574]: terminating.
May 6 10:19:59 RT-AC66UB1 user.info preinit[1]: samba daemon is stopped
May 6 10:19:59 RT-AC66UB1 user.info preinit[1]: samba daemon is started
May 6 10:19:59 RT-AC66UB1 user.info wsdd2[738]: starting.
May 6 10:20:15 RT-AC66UB1 kern.info kernel: usblp 1-2:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2C17
May 6 10:20:15 RT-AC66UB1 kern.info kernel: usbcore: registered new interface driver usblp
May 6 10:20:15 RT-AC66UB1 lpr.notice p9100d[802]: Connection from ::ffff:10.0.0.20 port 58612 accepted
May 6 10:20:15 RT-AC66UB1 user.debug wsdd2[738]: 'Terminated' signal received.
May 6 10:20:15 RT-AC66UB1 user.info wsdd2[738]: terminating.
May 6 10:20:15 RT-AC66UB1 user.info preinit[1]: samba daemon is stopped
May 6 10:20:15 RT-AC66UB1 lpr.err p9100d[802]: read: Connection reset by peer
May 6 10:20:15 RT-AC66UB1 lpr.notice p9100d[802]: Finished job: 217436/217436 bytes sent to printer
May 6 10:20:15 RT-AC66UB1 lpr.err p9100d[802]: copy_stream: Connection reset by peer
May 6 10:20:15 RT-AC66UB1 user.info preinit[1]: samba daemon is started
May 6 10:20:15 RT-AC66UB1 user.info wsdd2[821]: starting.
Edytowany przez zakk87 dnia 06-05-2023 10:22
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
pedro |
Dodano 08-05-2023 10:18
|

Moderator

Posty: 1012
Dołączył: 21/09/2015 15:03
|
A włącz jeszcze w Admin -> Debug -> Enable segfault logging (reboot? nie pamiętam...).
Może coś więcej zobaczymy?
|
|
|
|
zakk87 |
Dodano 08-05-2023 10:35
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
dziwna sprawa ale nie mogę wejść przez WAN do nas-usb.asp ani web-mysql.asp
opcja segfault włączona. Na razie tylko pojawia się w logach:
Cytat May 8 10:29:23 RT-AC66UB1 kern.warn kernel: httpd/28249: potentially unexpected fatal signal 11.
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: Pid: 28249, comm: httpd
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: CPU: 0 Tainted: P (2.6.36.4brcmarm #70)
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: PC is at 0x4041adc8
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: LR is at 0x19110
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: pc : [<4041adc8>] lr : [<00019110>] psr: 20000010
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: sp : be882ed8 ip : 4041adc0 fp : be882f88
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: r10: 00038b38 r9 : be882f68 r8 : 00000000
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: r7 : be882ee8 r6 : 0004005b r5 : be882ee8 r4 : 00000000
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: r3 : be882f88 r2 : 0000001d r1 : 00000000 r0 : be882f88
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: Flags: nzCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user
May 8 10:29:23 RT-AC66UB1 kern.warn kernel: Control: 10c53c7d Table: 9cc1004a DAC: 00000015
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: httpd/29490: potentially unexpected fatal signal 11.
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: Pid: 29490, comm: httpd
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: CPU: 0 Tainted: P (2.6.36.4brcmarm #70)
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: PC is at 0x4041adc8
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: LR is at 0x19110
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: pc : [<4041adc8>] lr : [<00019110>] psr: 20000010
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: sp : be882ed8 ip : 4041adc0 fp : be882f88
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: r10: 00038b38 r9 : be882f68 r8 : 00000000
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: r7 : be882ee8 r6 : 0004005b r5 : be882ee8 r4 : 00000000
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: r3 : be882f88 r2 : 0000001d r1 : 00000000 r0 : be882f88
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: Flags: nzCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user
May 8 10:30:46 RT-AC66UB1 kern.warn kernel: Control: 10c53c7d Table: 9cd4004a DAC: 00000015
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: httpd/29491: potentially unexpected fatal signal 11.
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: Pid: 29491, comm: httpd
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: CPU: 0 Tainted: P (2.6.36.4brcmarm #70)
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: PC is at 0x4041adc8
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: LR is at 0x19110
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: pc : [<4041adc8>] lr : [<00019110>] psr: 20000010
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: sp : be882ed8 ip : 4041adc0 fp : be882f88
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: r10: 00038b38 r9 : be882f68 r8 : 00000000
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: r7 : be882ee8 r6 : 0004005b r5 : be882ee8 r4 : 00000000
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: r3 : be882f88 r2 : 0000001d r1 : 00000000 r0 : be882f88
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: Flags: nzCv IRQs on FIQs on Mode USER_32 ISA ARM Segment user
May 8 10:30:47 RT-AC66UB1 kern.warn kernel: Control: 10c53c7d Table: 9cd4004a DAC: 00000015
dopiero wieczorem będę mógł zrestartować usługę wydruku i spróbować coś druknąć w większej ilości, na razie od wczoraj
Cytat May 7 21:50:48 lpr notice p9100d[802] Connection from ::ffff:10.0.0.16 port 50180 accepted
May 7 21:50:49 lpr notice p9100d[802] Finished job: 359104/359104 bytes sent to printer # tutaj ok
May 7 21:57:58 lpr notice p9100d[802] Connection from ::ffff:10.0.0.16 port 50564 accepted ## wydruk nie wyszedł
May 7 22:09:03 lpr notice p9100d[21454] Connection from ::ffff:10.0.0.16 port 51022 accepted # tutaj także nie wyszedł
Scalony z 08 maja 2023 17:23:56:
Cytat dziwna sprawa ale nie mogę wejść przez WAN do nas-usb.asp ani web-mysql.asp
jestem w domu i wychodzi na to, że po włączeniu Admin -> Debug -> Enable segfault logging nie działają powyższe. Robię restart i zobaczymy co logi pokażą.
Scalony z 08 maja 2023 17:33:18:
po restarcie pierwsze co rzuciło mi się w oczy w dmesg
Cytat usb 1-2: device descriptor read/64, error -110
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: device descriptor read/64, error -110
usb 1-2: device descriptor read/64, error -110
usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: device descriptor read/8, error -110
usb 1-2: device descriptor read/8, error -110
usb 1-2: new high speed USB device using ehci_hcd and address 5
usb 1-2: device descriptor read/8, error -110
usb 1-2: device descriptor read/8, error -110
hub 1-0:1.0: unable to enumerate USB device on port 2
Scalony z 08 maja 2023 17:43:18:
ok, wystarczyło na chwilę wyłączyć core usb support.
Edytowany przez zakk87 dnia 08-05-2023 17:43
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
kobrawerde |
Dodano 08-05-2023 20:15
|

Power User

Posty: 361
Dołączył: 07/05/2008 20:07
|
może jakiś problem sprzętowy ? kabla usb / portu usb itd?
Netgear R7000 - FreshTomato Firmware 2024.3 K26ARM USB AIO-64K
Wi-Fi: Ubiquiti U6-Lite
|
|
|
|
zakk87 |
Dodano 08-05-2023 22:30
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
kabel jest nowy (z folii rozpakowany w styczniu), drukarkę wymieniłem niedawno. Ciężko mi powiedzieć co do routera ale wcześniej miałem RT-N18U i było podobnie.
Cytat May 8 22:28:51 RT-AC66UB1 lpr.notice p9100d[13753]: Connection from ::ffff:10.0.0.20 port 62363 accepted
May 8 22:28:51 RT-AC66UB1 lpr.err p9100d[13753]: read: Connection reset by peer
May 8 22:28:51 RT-AC66UB1 lpr.notice p9100d[13753]: Finished job: 43224/43224 bytes sent to printer
May 8 22:28:51 RT-AC66UB1 lpr.err p9100d[13753]: copy_stream: Connection reset by peer
wydruk z pc poszedł. Zobaczymy za kilka dni.
Scalony z 19 maja 2023 20:36:41:
uptime 8 dni na 2023.1 i wydruk wyszedł.
Scalony z 07 czerwca 2023 16:51:38:
2023.1 uptime 26 dni. Drukuje
Wgrywam 2023.2.
Edytowany przez zakk87 dnia 07-06-2023 16:51
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|
|
pedro |
Dodano 08-06-2023 20:21
|

Moderator

Posty: 1012
Dołączył: 21/09/2015 15:03
|
OK, zobaczymy.
|
|
|
|
zakk87 |
Dodano 10-06-2023 12:56
|

User

Posty: 129
Dołączył: 19/06/2020 12:59
|
Wydruk wyszedł zaraz po wgraniu tomato 7 czerwca i dziś Uptime 2 dni także wyszedł.
Scalony z 20 czerwca 2023 14:01:16:
uptime 12 dni, wydruki dziś wyszły. Nie wiem co się wydarzyło poprzednim razem po update do 2023.2 ale teraz wszystko działa.
Scalony z 04 maja 2025 20:01:21:
Temat wraca jak bumerang. Mam teraz nawet inną drukarkę HP 1022, kabel nowy jak wcześniej wspomniałem.
Obecnie wygląda tak, uptime 41 dni, 30 kwietnia wyszło kilka wydruków
Cytat Apr 30 20:59:53 lpr notice p9100d[779] Finished job: 5396/5396 bytes sent to printer
Apr 30 21:01:00 lpr notice p9100d[779] Finished job: 6848/6848 bytes sent to printer
Apr 30 21:01:29 lpr notice p9100d[779] Finished job: 61092/61092 bytes sent to printer
dziś próbowałem puścić wydruk z dwóch smartfonów - nic. Z PC - nic.
W USB support drukarka jest widoczna. Dopiero po wyłączeniu udługi USB i włączeniu mogłem puścić wydruki.
Cytat May 4 19:51:54 kern info kernel usblp 1-2:1.0: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x2C17
May 4 19:52:16 lpr notice p9100d[27606] Finished job: 24488/24488 bytes sent to printer
Wygląda to jakby usługa wydruku lub USB usypiała się po x czasu.
Edytowany przez zakk87 dnia 04-05-2025 20:01
Freshtomato 2024.5 AIO @ RT-AC66U_B1
OpenWRT 24.10 @ DIR-1960
NAS OMV [CoolerMaster ELITE 110] [J1900I-C] [4GB RAM] [2xToshiba HDWD130 + Hitachi 5K3000]
|
|
|