Ogółem głosów: 416
Musisz zalogować się, aby móc zagłosować. Rozpoczęto: 02/02/2015 09:38
Twoje IP
3.17.186.218
Hacked WVC54G
This is a hacked version of the original Linksys
Firmware for the WVC54G Wireless-G Web Cam. Features:
- Added OLSR daemon for meshing
- Change Web-UI "Home" Link
- Added some wireless settings (Rts, Frag, TxPwr)
Changelog:
- Added olsr stability cron job. Because there is no
awk in the FW, a simple reboot is done if olsrd
dies or if the Ad-Hoc channel toggles to a channel
different to the channel setting of web UI.
- Changed the default olsrd parameters to lower CPU
percentage (will slow routing change propagation too)
- Added ether setup: If you start camera with unplugged
etherwire, the WLAN iface comes up. Normally, the eth
iface is not active if you plug in the etherwire now.
This change allows you to contact 192.168.1.115 via
eth. To configue another IP, add "lan_ip_addr=",
"lan_netmask" and "lan_broadcast" to /etc/system.conf.
To make changes permanent, change any value on the
web ui - then revert to old web ui setting.
- Added web admin user with web admin password for telnet
login. The root telnet login is diabled. If you change
to web admin user to the name "root", no telnet is
possible. Added "crypt" command for this.
- Added "lan_olsr=" setting to /etc/system.conf. This will
add the ether iface to /etc/olsrd.conf. But: If the
camera restarts with attached etherwire, the WLAN iface
will not come up. Only cable plug is necessary, no link
detection on eth occur. Sorry, no sourcecode for the
criticla /etc/rc.network program.
This means: It is not possible in the moment to use the
WVC as OLSR-Gateway with 2 interfaces (since you have to
plug out the etherwire manually during restart and restart
will happen once a day/week if something is wrong).
WLAN-only node in OLSR-Mesh will work of course.
- Added wl_rts=, wl_frag= and wl_txpwr= in /etc/system.conf
Added user_rc= also (you may add shell commands executed
during startup here).
- Changed kernel config to include /proc/sys (to enable
ip forwarding for expample). Linksys orig comes without.
· Łącznie użytkowników: 24,117 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Adooni
26-04-2024 14:41
jaki router RMerlin nie pociagne, tomato/ openwrt tak non hilink,
tamtosiamto
23-04-2024 12:35
modem bez smilocka?
man1
22-04-2024 23:27
Czy próbował ktoś uzywac karty voice (z nolimit GB) od tmobile w modemie /routerze? Da się jakoś to zrobić? Bo u mnie neta brak. E3372
tamtosiamto
31-03-2024 12:54
Wesolego jajka wszytskim forumowiczom
tamtosiamto
28-03-2024 23:24
tak, tak zgadza sie, ale ja pytam o wykluczenie noda na guest network w first set, i to nie dziala
Adooni
24-03-2024 13:16
Guest network is currently designed to allow the first set of each band (2.4G, 5G, 5G-1) available to the AiMesh node
tamtosiamto
24-03-2024 03:03
ale w 1 jest opcja do wyboru - dla calej sieci albo rutera only i wlasnie o tym mowie, ze nie dziala
Adooni
23-03-2024 16:31
w dokumencie asusa jest ze wlasnie dla 1 ma dzialac na nodach tez
tamtosiamto
23-03-2024 15:39
tak, ale nie zmienia to faktu, ze w pierwszej nie dziala wylaczanie aimesh dla goscinnej( a powinno), czyli jest jakis bug. Mam start soft, bo to dsl-ac68 ktory nie jest juz updateowany
Adooni
22-03-2024 18:07
nie, 1 wsza bedzie wszedzie trzeba 2ga zrobic dla kazdego pasma te nie sa przenoszone