Ogółem głosów: 416
Musisz zalogować się, aby móc zagłosować. Rozpoczęto: 02/02/2015 09:38
Twoje IP
3.81.222.152
PAP2-T nowe firmware 5.1.6
Właśnie ukazało się nowe firmware dla bardzo popularnej bramki VoIP pap2-t , oprogramowanie można pobrać
ze strony linksysa.
Lista zmian:
Release Notes for -- Linksys PAP2/PAP2T 5.1.6
PAP2 -- 2 Port FXS, 1 Ethernet Interface
PAP2T -- 2 Port FXS, 1 Ethernet Interface
Copyright (C) 2007 by Linksys, a Division of Cisco Systems, Inc.
All Rights Reserved.
* * * * * * * * * * IMPORTANT * * * * * * * * * * * * * * * * *
* Use of Proprietary Information and Copyright Notice: *
* This release note document contains proprietary information *
* that is to be used only by Sipura Technology, Linksys(R), *
* and Cisco Systems, Inc. customers. Any unauthorized *
* disclosure, copying, distribution, or use of this *
* information is prohibited. This restriction includes *
* ALL Internet based discussion forums, e.g. DSLreports. *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
/** NOTICE **/
official release
========================================
New Features
========================================
--- External Notes ---
- If REGISTER results in a 301 response with a Contact header
that has a maddr URI parameter, and if the
is an IP address, the SPA will change the outproxy proxy
address to the value of the maddr address. This value will
remain valid until the next 301 response, if any, or will
restore to the originally configured value upon reboot.
- When swapping calls in a call-waiting or similar situation,
the SPA will order the operations to make sure that call hold
is invoked before call resume.
- New RC blink pattern. Power LED red-orange slow blink while
contacting server. Red-orange double blink if file not found
or corrupt.
- 1. Make DHCP DISCOVER retry longer (120 Seconds)2. Reboot the
device in 10 minutes if the device is using last konwn good
IP address.
- SDP in INVITE response, includes annexb=yes/no if present in
INVITE message
- Fixed this problem: A,B,C,D digits are dropped when dialing
- SPA should escape occurrences of '#' in the dial string with
%23 in outbound INVITE
- Fixed this problem: Unit stops playing incoming RTP audio once
it receives a 180/183 w/o SDP; regardless setting of
parameter
- bug fix: Bogus IP may be used if dns srv failed when querying
the proxy server.
- Worked around this problem: some server will change the Contact
header's address in their response to the SPA's SIP REGISTER
request, so that the SPA cannot find the corresponding Contact
in the response and therefore may not be able to extract the
proper expires value inserted by the server. This is a problem
if the expires value inserted by the server in the response is
smaller than the value in the original SIP REGISTER request.
The work around is to use the first entry in the Contact header
if an exactly matching address is not found.
- Fixed this problem: If unknown response is received, such as 101,
SPA might misinterpret it as a 6xx response. In some other cases,
an unknown response, such as 188, might be dropped by the SPA as
a bad message. The proper way is to treat it as the corresponding
base response, such as 100.
- Fixed this problem: Daylight Saving Time is not correct if start
time is later then end time of the year in the
Time Rule> parameter
- Fixed this problem: Unit should ignore in-dialog re-INVITE if it
has not received ACK to the 200 response to the initial INVITE
from the caller. This condition might happen if the ACK was lost
but the first re-INVITE has already been sent by the peer.
- Fixed this problem: Unit should not filter out leading * or #
digit in the incoming caller id number, as these can be legitimate
phone number digits
- Fixed this problem: PAP2T cannot detect DTMF digits at 50ms on/off
during a call, even if is "normal".
- Fixed missing '*' and '#' in on-hook caller-id number generation
- Eliminated cause of spurious reboot on resync for customized units
with read-only parameters and value mismatch.
· Łącznie użytkowników: 24,117 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Adooni
24-03-2024 13:16
Guest network is currently designed to allow the first set of each band (2.4G, 5G, 5G-1) available to the AiMesh node
tamtosiamto
24-03-2024 03:03
ale w 1 jest opcja do wyboru - dla calej sieci albo rutera only i wlasnie o tym mowie, ze nie dziala
Adooni
23-03-2024 16:31
w dokumencie asusa jest ze wlasnie dla 1 ma dzialac na nodach tez
tamtosiamto
23-03-2024 15:39
tak, ale nie zmienia to faktu, ze w pierwszej nie dziala wylaczanie aimesh dla goscinnej( a powinno), czyli jest jakis bug. Mam start soft, bo to dsl-ac68 ktory nie jest juz updateowany
Adooni
22-03-2024 18:07
nie, 1 wsza bedzie wszedzie trzeba 2ga zrobic dla kazdego pasma te nie sa przenoszone
tamtosiamto
19-03-2024 19:57
czyli jak mam jedna siec goscinna to powinno dzialac separowanie gosci od noda -a nie dziala
tamtosiamto
19-03-2024 19:50
@Adooni 'Only one set is available for 1 band' i tak mam-1 set dla 2.4ghz i 1 dla 5ghz-czy czegos nie rozumiemW drugiej sieci goscinnej nie ma opcji wyboru Ruter only/ All nodes
Adooni
19-03-2024 19:14
no to przeczytaj to 2 pod - 1 stet z kazdego pasma jest dopuszczony na nody. zrob 2 siec jako goscinna na danym pasmie i wtedy sprawdz
tamtosiamto
19-03-2024 14:17
@Adooni 'Guest network on AiMesh - Router only'
Adooni
18-03-2024 19:20
Asus napisał coś takiego Note: Guest network is currently designed to allow the first set of each band (2.4G, 5G, 5G-1) available to the AiMesh node. Only one set is available for each band.
w 02 grudnia 2007 00:44:41
w 03 grudnia 2007 19:47:58