Z tego co się orientuję te błędy pojawiają się dlatego, że dnsmasq ma włączoną opcję "stop-dns-rebind" i ktoś próbował ataku DNS-rebind. W dużym skrócie chodzi o blokadę (i logowanie) odpowiedzi z nadrzędnych DNSów, które są adresami prywatnymi (stosowane do ataków na sieci lokalne, np. do zmiany konfiguracji routerów). Zakres IP odpowiadający puli adresów prywatnych jest filtrowany, gdy wspomniana opcja dnsmasq jest włączona. Przynajmniej ja tak rozumiem działanie tej opcji
[small]Pozdrawiam, Monter Asus RT-N18 + FreshTomato 2019.3 K26ARM USB AIO-64K-NOSMP + ILHM v2 HTPC Chieftec FLYER FI-02BC-U3 + GA-H61N-USB3 + i3-3225 + 4GB RAM + LibreELEC + Xbox DVD Remot
Z tego co się orientuję te błędy pojawiają się dlatego, że dnsmasq ma włączoną opcję "stop-dns-rebind" i ktoś próbował ataku DNS-rebind. W dużym skrócie chodzi o blokadę (i logowanie) odpowiedzi z nadrzędnych DNSów, które są adresami prywatnymi (stosowane do ataków na sieci lokalne, np. do zmiany konfiguracji routerów). Zakres IP odpowiadający puli adresów prywatnych jest filtrowany, gdy wspomniana opcja dnsmasq jest włączona. Przynajmniej ja tak rozumiem działanie tej opcji
mam odptaszkowane" Zapobiegaj atakom DNS-rebind" czyli funkcja sie sprawdziła
dzieki za odpowiedz
Asus RT-N10U v.B1 ||Tomato-K26USB-1.28.RT-N5x-MIPSR2-115-PL-Nocat-VPN|| Linksys E 2500 OFW 1.0.0.7
Shibby, mam nadzieję, że to co proponujesz usuwa _tylko_ komunikaty, a nie np wyłącza ochronę? Pytam, bo niestety tego nie doprecyzowałeś. Co prawda ciężko z góry podejrzewać, że aby usunąć komunikat zalecasz komuś wyłączyć ochronę przed atakami, ale zawsze lepiej się upewnić
[small]Pozdrawiam, Monter Asus RT-N18 + FreshTomato 2019.3 K26ARM USB AIO-64K-NOSMP + ILHM v2 HTPC Chieftec FLYER FI-02BC-U3 + GA-H61N-USB3 + i3-3225 + 4GB RAM + LibreELEC + Xbox DVD Remot
Jestem jak najbardziej poważny. Nie pytałem o ipv4/6, tylko konkretnie o dns-rebind. Brak jakiejkolwiek szczegółowej instrukcji całego Tomato z opisem co właściwie robi dany przełącznik (nie wszystko jest intuicyjne) wymusza takie pytania, nie tylko u laików. Ponadto opis opcji w zakładce Advanced DHCP/DNS mówi tak: "Prevent DNS-rebind attacks" - skąd uiser ma wiedzieć, że odptaszkowując to nie wyłączy sobie tym ochrony, skoro ten ptaszek jest w ustawieniach zaawansowanych routera? Jak wyłącza tylko logi to czy nie powinien być w Administration -> Logging? Nie, żebym się czepiał ale trochę ta lokalizacja myląca skoro tylko o logi chodzi. No chyba, że mówisz o innej opcji niż "Prevent DNS-rebind attacks" ze wspomnianej zakładki?
[small]Pozdrawiam, Monter Asus RT-N18 + FreshTomato 2019.3 K26ARM USB AIO-64K-NOSMP + ILHM v2 HTPC Chieftec FLYER FI-02BC-U3 + GA-H61N-USB3 + i3-3225 + 4GB RAM + LibreELEC + Xbox DVD Remot
Przecież router może korzystać z tego jak ze źródła internetu przez wifi (MiFi AP - Tomato APC/WIPS) inaczej się raczej nie da.
Raczej chyba jest możliwość taki modem działa jako karta sieciowa (moduł usb-ether jak dobrze pamiętam)
W OpenWrt trzeba to robić ręcznie. W Oleg firmware jest z GUI ale brakuje innych opcji. Tych modemo-routerów jest coraz więcej i przydałaby się jego obsługa. Co do Wifi to można by to tak rozwiązać ale jest to uciążliwe i prawdopodobnie mniej wydajne niż połączenie przez usb
Asus RT-N16, TP-LINK WDR4300, ASUS RT-AC68U, D-LINK DIR-882
Witam
Mam router Asus RT-N66U
Podłączyłem modem usb Huawei e169 z kartą aero.
w Podstawowe-> typ:Model 3G
Urządzenie 3gdev/ttyUSB0 (tego ustawienia nie jestem pewny, bo mam 2 porty usb i nie wiem jak sprawdzić, który to)
APN darmowy
w USB i NAS mam zaznaczoną obsługę usb, usb2.0, usb 1.1, OHCI, Obsługę modemów USB.
w podłączonych urządzeniach jest HUAWEI Mass Storage (nie zamontowane).
Męczę się od kilku godzin. Próbowałem się połączyć przez skrypty, ale nic nie pomaga. Ma ktoś jakiś pomysł?
Na początek wystarczy mi informacja, czy sterowniki wifi z softów MariuszNM/1.28ND-SM/ oraz Tomato PL 1.28.0005 083V-PL ND VPN są identyczne
nie. Ten w 1.28-SM pochodzi z oryginalnego tomato 1.28 czyli jest mega stary ale za to najbardziej wydajny w WRT54G/GL/GS. Jest w 083 jest dużo nowszy ale na starym sprzęcie może być gorsza wydajność sieci. Po prostu nowy sterownik jest po to by wspierać nowsze sprzęty a nie koniecznie poprawiać wydajność i stabilność starych sprzętów.
Dzięki, a co z drugą częścią mojego pytania?, zatem czy na oryginalnym sofcie linksysa sieć wifi będzie działała lepiej ( wydajniej) , niż na jakimkolwiek sofcie alternatywnym? Jest sens wracać?
@lew487 - ok już widzę gdzie jest problem. Po aktualizacji usbmodeswitch zmienił się format jego wywołania i widzę, że z plików data zniknęły nie tylko wpisy default ale w niektórych przypadkach również i target i dlatego nie działa w twoim przypadku skrypt przełączania.
Aktualizacja usbmodeswitch była w wersji v110 tak więc póki co polecam wgrać 108 lub 109 i poczekaj na nowe wydanie.
Proxmox VE:i7-7700T, 64GB RAM, 3x2TB SSD, 1x1TB SSD, 512GB NVMe, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology DS920+ VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
@lew487 - ok już widzę gdzie jest problem. Po aktualizacji usbmodeswitch zmienił się format jego wywołania i widzę, że z plików data zniknęły nie tylko wpisy default ale w niektórych przypadkach również i target i dlatego nie działa w twoim przypadku skrypt przełączania.
Aktualizacja usbmodeswitch była w wersji v110 tak więc póki co polecam wgrać 108 lub 109 i poczekaj na nowe wydanie.
A dlaczego mam wgrać v108/109 a nie v110 lub v112 ?
w tej chwili mam wgrany Tomato PL 1.28.0000 MIPSR2-105-PL K26 USB AIO-64K
Przełączałem po kolei każdy interfejs usb i niestety nadal nie chce się połączyć.
Co do koloru diody to miga na niebiesko. Na poprzednim sofcie też tak było.
Jan 1 01:00:48 unknown syslog.info syslogd started: BusyBox v1.20.2
Jan 1 01:00:48 unknown user.notice kernel: klogd started: BusyBox v1.20.2 (2013-03-27 18:28:42 CET)
Jan 1 01:00:48 unknown user.notice kernel: Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #5 Wed Mar 27 18:54:49 CET 2013
Jan 1 01:00:48 unknown user.warn kernel: CPU revision is: 00019749
Jan 1 01:00:48 unknown user.warn kernel: Determined physical RAM map:
Jan 1 01:00:48 unknown user.warn kernel: memory: 07fff000 @ 00000000 (usable)
Jan 1 01:00:48 unknown user.warn kernel: memory: 08000000 @ 87fff000 (usable)
Jan 1 01:00:48 unknown user.debug kernel: Entering add_active_range(0, 0, 32767) 0 entries of 256 used
Jan 1 01:00:48 unknown user.debug kernel: Entering add_active_range(0, 557055, 589823) 1 entries of 256 used
Jan 1 01:00:48 unknown user.info kernel: Zone PFN ranges:
Jan 1 01:00:48 unknown user.err syslog: module usbcore not found in modules.dep
Jan 1 01:00:48 unknown user.warn kernel: Normal 0 -> 131072
Jan 1 01:00:48 unknown user.warn kernel: HighMem 131072 -> 589823
Jan 1 01:00:48 unknown user.info kernel: early_node_map[2] active PFN ranges
Jan 1 01:00:48 unknown user.warn kernel: 0: 0 -> 32767
Jan 1 01:00:48 unknown user.warn kernel: 0: 557055 -> 589823
Jan 1 01:00:48 unknown user.debug kernel: On node 0 totalpages: 65535
Jan 1 01:00:48 unknown user.debug kernel: Normal zone: 0 pages used for memmap
Jan 1 01:00:48 unknown user.debug kernel: Normal zone: 0 pages reserved
Jan 1 01:00:48 unknown user.debug kernel: Normal zone: 32767 pages, LIFO batch:7
Jan 1 01:00:48 unknown user.debug kernel: HighMem zone: 0 pages used for memmap
Jan 1 01:00:48 unknown user.debug kernel: HighMem zone: 32768 pages, LIFO batch:7
Jan 1 01:00:48 unknown user.warn kernel: Built 1 zonelists. Total pages: 65535
Jan 1 01:00:48 unknown user.notice kernel: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Jan 1 01:00:48 unknown user.warn kernel: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Jan 1 01:00:48 unknown user.warn kernel: Primary data cache 32kB, 4-way, linesize 32 bytes.
Jan 1 01:00:48 unknown user.info kernel: Synthesized TLB refill handler (20 instructions).
Jan 1 01:00:48 unknown user.info kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan 1 01:00:48 unknown user.info kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan 1 01:00:48 unknown user.info kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan 1 01:00:48 unknown user.warn kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Jan 1 01:00:48 unknown user.warn kernel: CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Jan 1 01:00:48 unknown user.warn kernel: Using 300.000 MHz high precision timer.
Jan 1 01:00:48 unknown user.info kernel: console [ttyS0] enabled
Jan 1 01:00:48 unknown user.warn kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 01:00:48 unknown user.warn kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 01:00:48 unknown user.info kernel: Memory: 255300k/131068k available (33k kernel code, 6536k reserved, 2941k data, 128k init, 131072k highmem)
Jan 1 01:00:48 unknown user.debug kernel: Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
Jan 1 01:00:48 unknown user.warn kernel: Mount-cache hash table entries: 512
Jan 1 01:00:48 unknown user.info kernel: NET: Registered protocol family 16
Jan 1 01:00:48 unknown user.info kernel: usbcore: registered new interface driver usbfs
Jan 1 01:00:48 unknown user.info kernel: usbcore: registered new interface driver hub
Jan 1 01:00:48 unknown user.info kernel: usbcore: registered new device driver usb
Jan 1 01:00:48 unknown user.warn kernel: PCI: Initializing host
Jan 1 01:00:48 unknown user.warn kernel: PCI: Reset RC
Jan 1 01:00:48 unknown user.warn kernel: PCI: Initializing host
Jan 1 01:00:48 unknown user.warn kernel: PCI: Reset RC
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bus 0
Jan 1 01:00:48 unknown user.warn kernel: PCI/PCIe coreunit 0 is set to bus 1.
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:48 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:00.0 to 64
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:48 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:00.1 to 64
Jan 1 01:00:48 unknown user.warn kernel: PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bus 1
Jan 1 01:00:48 unknown user.warn kernel: PCI/PCIe coreunit 1 is set to bus 2.
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:48 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:00.0 to 64
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:48 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:00.1 to 64
Jan 1 01:00:48 unknown user.warn kernel: PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
Jan 1 01:00:48 unknown user.warn kernel: PCI: Fixing up bus 2
Jan 1 01:00:48 unknown user.info kernel: NET: Registered protocol family 2
Jan 1 01:00:48 unknown user.info kernel: Time: MIPS clocksource has been installed.
Jan 1 01:00:48 unknown user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:48 unknown user.warn kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan 1 01:00:48 unknown user.warn kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 01:00:48 unknown user.info kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan 1 01:00:48 unknown user.info kernel: TCP reno registered
Jan 1 01:00:48 unknown user.warn kernel: highmem bounce pool size: 64 pages
Jan 1 01:00:48 unknown user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
Jan 1 01:00:48 unknown user.info kernel: io scheduler noop registered (default)
Jan 1 01:00:48 unknown user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
Jan 1 01:00:48 unknown user.info kernel: N_HDLC line discipline registered.
Jan 1 01:00:48 unknown user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan 1 01:00:48 unknown user.info kernel: serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
Jan 1 01:00:48 unknown user.info kernel: serial8250: ttyS1 at MMIO 0xb8000400 (irq = 8) is a 16550A
Jan 1 01:00:48 unknown user.info kernel: PPP generic driver version 2.4.2
Jan 1 01:00:48 unknown user.info kernel: MPPE/MPPC encryption/compression module registered
Jan 1 01:00:48 unknown user.info kernel: NET: Registered protocol family 24
Jan 1 01:00:48 unknown user.info kernel: PPPoL2TP kernel driver, V0.18.3
Jan 1 01:00:48 unknown user.info kernel: PPTP driver version 0.8.5
Jan 1 01:00:48 unknown user.info kernel: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan 1 01:00:48 unknown user.debug hotplug[412]: Attached USB device 1-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/2/206]
Jan 1 01:00:48 unknown user.warn kernel: Amd/Fujitsu Extended Query Table at 0x0040
Jan 1 01:00:48 unknown user.warn kernel: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan 1 01:00:48 unknown user.notice kernel: number of CFI chips: 1
Jan 1 01:00:48 unknown user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan 1 01:00:48 unknown user.notice kernel: Flash device: 0x2000000 at 0x1c000000
Jan 1 01:00:48 unknown user.notice kernel: Creating 5 MTD partitions on "Physically mapped flash":
Jan 1 01:00:48 unknown user.notice kernel: 0x00000000-0x00040000 : "pmon"
Jan 1 01:00:48 unknown user.notice kernel: 0x00040000-0x01fe0000 : "linux"
Jan 1 01:00:48 unknown user.notice kernel: 0x00139c00-0x009a0000 : "rootfs"
Jan 1 01:00:48 unknown user.notice kernel: 0x009a0000-0x01fe0000 : "jffs2"
Jan 1 01:00:48 unknown user.notice kernel: 0x01fe0000-0x02000000 : "nvram"
Jan 1 01:00:48 unknown user.warn kernel: Found an serial flash with 0 0KB blocks; total size 0MB
Jan 1 01:00:48 unknown user.err kernel: sflash: found no supported devices
Jan 1 01:00:48 unknown user.warn kernel: _nvram_init: allocat header: 2280980480, size= 65536
Jan 1 01:00:48 unknown user.info kernel: usbcore: registered new interface driver hiddev
Jan 1 01:00:48 unknown user.info kernel: usbcore: registered new interface driver usbhid
Jan 1 01:00:48 unknown user.info kernel: drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Jan 1 01:00:48 unknown user.warn kernel: u32 classifier
Jan 1 01:00:48 unknown user.warn kernel: OLD policer on
Jan 1 01:00:48 unknown user.warn kernel: Netfilter messages via NETLINK v0.30.
Jan 1 01:00:48 unknown user.warn kernel: nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
Jan 1 01:00:48 unknown user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:48 unknown user.info kernel: ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
Jan 1 01:00:48 unknown user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Mar 27 2013 18:53:49]
Jan 1 01:00:49 unknown user.info kernel: NET: Registered protocol family 1
Jan 1 01:00:49 unknown user.info kernel: NET: Registered protocol family 10
Jan 1 01:00:49 unknown user.warn kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:49 unknown user.info kernel: NET: Registered protocol family 17
Jan 1 01:00:49 unknown user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear
Jan 1 01:00:49 unknown user.info kernel: All bugs added by David S. Miller
Jan 1 01:00:49 unknown user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:49 unknown user.info kernel: Freeing unused kernel memory: 128k freed
Jan 1 01:00:49 unknown user.warn kernel: Warning: unable to open an initial console.
Jan 1 01:00:49 unknown user.warn kernel: emf: module license 'Proprietary' taints kernel.
Jan 1 01:00:49 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 01:00:49 unknown user.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.20
Jan 1 01:00:49 unknown user.warn kernel: wl_module_init: passivemode set to 0x0
Jan 1 01:00:49 unknown user.warn kernel: PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
Jan 1 01:00:49 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:01.0 to 64
Jan 1 01:00:49 unknown user.warn kernel: eth1: Broadcom BCM4331 802.11 Wireless Controller 5.100.138.20
Jan 1 01:00:49 unknown user.debug hotplug[452]: Attached USB device 2-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/1/206]
Jan 1 01:00:49 unknown user.debug hotplug[457]: Attached USB device 1-1:1.0 [INTERFACE=9/0/0 PRODUCT=58f/6254/100]
Jan 1 01:00:49 unknown user.warn kernel: PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
Jan 1 01:00:49 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:01.0 to 64
Jan 1 01:00:49 unknown user.warn kernel: eth2: Broadcom BCM4331 802.11 Wireless Controller 5.100.138.20
Jan 1 01:00:49 unknown user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:49 unknown user.notice kernel: SCSI subsystem initialized
Jan 1 01:00:49 unknown user.info kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:49 unknown user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 01:00:49 unknown user.info kernel: USB Mass Storage support registered.
Jan 1 01:00:49 unknown user.info kernel: sdhci: Secure Digital Host Controller Interface driver
Jan 1 01:00:49 unknown user.info kernel: sdhci: Copyright(c) Pierre Ossman
Jan 1 01:00:49 unknown user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 01:00:49 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:04.1 to 64
Jan 1 01:00:49 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
Jan 1 01:00:49 unknown user.info kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
Jan 1 01:00:49 unknown user.info kernel: ehci_hcd 0000:00:04.1: irq 6, io mem 0x18004000
Jan 1 01:00:49 unknown user.info kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
Jan 1 01:00:49 unknown user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 01:00:49 unknown user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 01:00:49 unknown user.info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 01:00:49 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:04.0 to 64
Jan 1 01:00:49 unknown user.info kernel: ohci_hcd 0000:00:04.0: OHCI Host Controller
Jan 1 01:00:49 unknown user.info kernel: ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
Jan 1 01:00:49 unknown user.info kernel: ohci_hcd 0000:00:04.0: irq 6, io mem 0x18009000
Jan 1 01:00:49 unknown user.info kernel: usb usb2: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.info kernel: hub 2-0:1.0: USB hub found
Jan 1 01:00:49 unknown user.info kernel: hub 2-0:1.0: 2 ports detected
Jan 1 01:00:49 unknown user.info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2
Jan 1 01:00:49 unknown user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.info kernel: hub 1-1:1.0: USB hub found
Jan 1 01:00:49 unknown user.info kernel: hub 1-1:1.0: 4 ports detected
Jan 1 01:00:49 unknown user.debug kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:49 unknown user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:00:49 unknown user.info kernel: vlan1: dev_set_allmulti(master, 1)
Jan 1 01:00:49 unknown user.info kernel: vlan1: dev_set_promiscuity(master, 1)
Jan 1 01:00:49 unknown user.info kernel: device eth0 entered promiscuous mode
Jan 1 01:00:49 unknown user.info kernel: device vlan1 entered promiscuous mode
Jan 1 01:00:49 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.1: new high speed USB device using ehci_hcd and address 3
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.1: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.debug hotplug[482]: Attached USB device 1-1.1:1.0 [INTERFACE=8/6/80 PRODUCT=90c/1000/1100]
Jan 1 01:00:49 unknown user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 01:00:49 unknown user.info kernel: Registered led device: 1-1.1
Jan 1 01:00:49 unknown user.info kernel: device eth2 entered promiscuous mode
Jan 1 01:00:49 unknown user.info kernel: br0: port 3(eth2) entering forwarding state
Jan 1 01:00:49 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:49 unknown user.info kernel: br0: port 1(vlan1) entering forwarding state
Jan 1 01:00:49 unknown user.warn kernel: vlan2: Setting MAC address to 08 60 6e bb 7f e1.
Jan 1 01:00:49 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:49 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.2: new full speed USB device using ehci_hcd and address 4
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.2: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.warn kernel: usb-storage: probe of 1-1.2:1.0 failed with error -5
Jan 1 01:00:49 unknown user.warn kernel: usb-storage: probe of 1-1.2:1.1 failed with error -5
Jan 1 01:00:49 unknown user.warn kernel: usb-storage: probe of 1-1.2:1.2 failed with error -5
Jan 1 01:00:49 unknown user.info kernel: scsi4 : SCSI emulation for USB Mass Storage devices
Jan 1 01:00:49 unknown user.debug hotplug[506]: Attached USB device 1-1.2:1.0 [INTERFACE=255/255/255 PRODUCT=12d1/1001/0]
Jan 1 01:00:49 unknown user.debug hotplug[509]: Attached USB device 1-1.2:1.1 [INTERFACE=255/255/255 PRODUCT=12d1/1001/0]
Jan 1 01:00:49 unknown user.debug hotplug[512]: Attached USB device 1-1.2:1.2 [INTERFACE=255/255/255 PRODUCT=12d1/1001/0]
Jan 1 01:00:49 unknown user.debug hotplug[515]: Attached USB device 1-1.2:1.3 [INTERFACE=8/6/80 PRODUCT=12d1/1001/0]
Jan 1 01:00:49 unknown user.info kernel: Registered led device: 1-1.2
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.4: new high speed USB device using ehci_hcd and address 5
Jan 1 01:00:49 unknown user.info kernel: IMQ starting with 2 devices...
Jan 1 01:00:49 unknown user.info kernel: IMQ driver loaded successfully.
Jan 1 01:00:49 unknown user.info kernel: Hooking IMQ after NAT on PREROUTING.
Jan 1 01:00:49 unknown user.info kernel: Hooking IMQ before NAT on POSTROUTING.
Jan 1 01:00:49 unknown user.info kernel: usb 1-1.4: configuration #1 chosen from 1 choice
Jan 1 01:00:49 unknown user.info kernel: scsi5 : SCSI emulation for USB Mass Storage devices
Jan 1 01:00:49 unknown user.debug hotplug[541]: Attached USB device 1-1.4:1.0 [INTERFACE=8/6/80 PRODUCT=58f/6366/100]
Jan 1 01:00:50 unknown daemon.err pppd[589]: In file /tmp/ppp/wanoptions: unrecognized option '/dev/ttyUSB2'
Jan 1 01:00:50 unknown authpriv.info dropbear[603]: Running in background
Jan 1 01:00:50 unknown user.info redial[594]: Started. Time: 10
Jan 1 01:00:51 unknown daemon.info dnsmasq[648]: started, version UNKNOWN cachesize 1500
Jan 1 01:00:51 unknown daemon.info dnsmasq[648]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack Tomato-helper auth
Jan 1 01:00:51 unknown daemon.info dnsmasq[648]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 01:00:51 unknown daemon.info dnsmasq-dhcp[648]: DHCP, IP range 192.168.1.3 -- 192.168.1.51, lease time 1d
Jan 1 01:00:51 unknown daemon.warn dnsmasq[648]: failed to access /etc/resolv.dnsmasq: No such file or directory
Jan 1 01:00:51 unknown daemon.info dnsmasq[648]: read /etc/hosts - 2 addresses
Jan 1 01:00:51 unknown daemon.info dnsmasq[648]: read /etc/dnsmasq/hosts/hosts - 4 addresses
Jan 1 01:00:51 unknown daemon.info dnsmasq-dhcp[648]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 01:00:51 unknown user.notice root: 3G MODEM FOUND - 12d1:1001 - Switching ...
Jan 1 01:00:51 unknown user.debug init[1]: starting rstats.
Jan 1 01:00:51 unknown user.notice kernel: scsi 0:0:0:0: Direct-Access USB 2.0 Flash Disk 1100 PQ: 0 ANSI: 0 CCS
Jan 1 01:00:51 unknown user.debug init[1]: starting cstats.
Jan 1 01:00:51 unknown user.notice kernel: sd 0:0:0:0: [sda] 1957888 512-byte hardware sectors (1002 MB)
Jan 1 01:00:51 unknown user.notice kernel: sd 0:0:0:0: [sda] Write Protect is off
Jan 1 01:00:51 unknown user.debug kernel: sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
Jan 1 01:00:51 unknown user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:51 unknown user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:51 unknown user.info kernel: sda: sda1
Jan 1 01:00:51 unknown user.notice kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan 1 01:00:51 unknown user.notice kernel: scsi 4:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Jan 1 01:00:51 unknown user.notice kernel: scsi 4:0:0:1: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
Jan 1 01:00:51 unknown user.notice kernel: sd 4:0:0:1: [sdb] Attached SCSI removable disk
Jan 1 01:00:51 unknown user.info kernel: EXT3-fs: starting recovery.
Jan 1 01:00:51 unknown user.notice root: 3G MODEM ready - 12d1:1001
Jan 1 01:00:51 unknown user.notice kernel: scsi 5:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
Jan 1 01:00:51 unknown user.notice kernel: sd 5:0:0:0: [sdc] Attached SCSI removable disk
Jan 1 01:00:51 unknown user.info kernel: usbcore: registered new interface driver cdc_acm
Jan 1 01:00:51 unknown user.info kernel: drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Jan 1 01:00:51 unknown user.info kernel: usbcore: registered new interface driver usbserial
Jan 1 01:00:51 unknown user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
Jan 1 01:00:51 unknown user.info kernel: usbcore: registered new interface driver usbserial_generic
Jan 1 01:00:51 unknown user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core
Jan 1 01:00:51 unknown user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
Jan 1 01:00:51 unknown user.info kernel: option 1-1.2:1.0: GSM modem (1-port) converter detected
Jan 1 01:00:51 unknown user.info kernel: usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
Jan 1 01:00:51 unknown user.info kernel: option 1-1.2:1.1: GSM modem (1-port) converter detected
Jan 1 01:00:51 unknown user.info kernel: usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1
Jan 1 01:00:52 unknown user.info kernel: option 1-1.2:1.2: GSM modem (1-port) converter detected
Jan 1 01:00:52 unknown user.info kernel: usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2
Jan 1 01:00:52 unknown user.info kernel: usbcore: registered new interface driver option
Jan 1 01:00:52 unknown user.info kernel: drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
Jan 1 01:00:52 unknown user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
Jan 1 01:00:52 unknown user.info kernel: usbcore: registered new interface driver sierra
Jan 1 01:00:52 unknown user.info kernel: drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
Jan 1 01:00:53 unknown user.info kernel: kjournald starting. Commit interval 5 seconds
Jan 1 01:00:53 unknown user.info hotplug[674]: USB ext3 fs at /dev/sda1 mounted on /tmp/mnt/sda1
Jan 1 01:00:53 unknown user.warn kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jan 1 01:00:53 unknown user.info kernel: EXT3 FS on sda1, internal journal
Jan 1 01:00:53 unknown user.info kernel: EXT3-fs: recovery complete.
Jan 1 01:00:53 unknown user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan 1 01:00:54 unknown user.notice root: 3G MODEM ready - using option module
Jan 1 01:00:59 unknown daemon.err apcupsd[448]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see .
Jan 1 01:00:59 unknown daemon.err apcupsd[448]: apcupsd error shutdown completed
Jan 1 01:01:10 unknown user.info redial[594]: WAN down. Reconnecting...
Jan 1 01:01:11 unknown daemon.err nmbd[794]: Samba server UNKNOWN is now a domain master browser for workgroup WORKGROUP on subnet UNICAST_SUBNET
Jan 1 01:01:12 unknown user.notice root: Stoping NFS Server ...
Jan 1 01:01:12 unknown user.notice root: NFS Server stoped ...
Jan 1 01:01:12 unknown user.notice root: Transmission daemon successfully stoped
Jan 1 01:01:12 unknown user.info init[1]: Asus RT-N66U: Tomato 1.28.0000 MIPSR2-108-PL K26 USB AIO-64K
Jan 1 01:01:12 unknown daemon.info dnsmasq[648]: exiting on receipt of SIGTERM
Jan 1 01:01:12 unknown user.debug init[1]: 182: pptp peerdns disabled
Jan 1 01:01:12 unknown daemon.info dnsmasq[839]: started, version UNKNOWN cachesize 1500
Jan 1 01:01:12 unknown daemon.info dnsmasq[839]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack Tomato-helper auth
Jan 1 01:01:12 unknown daemon.info dnsmasq[839]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 01:01:12 unknown daemon.info dnsmasq-dhcp[839]: DHCP, IP range 192.168.1.3 -- 192.168.1.51, lease time 1d
Jan 1 01:01:12 unknown daemon.warn dnsmasq[839]: no servers found in /etc/resolv.dnsmasq, will retry
Jan 1 01:01:12 unknown daemon.info dnsmasq[839]: read /etc/hosts - 2 addresses
Jan 1 01:01:12 unknown daemon.info dnsmasq[839]: read /etc/dnsmasq/hosts/hosts - 4 addresses
Jan 1 01:01:12 unknown daemon.info dnsmasq-dhcp[839]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 01:01:12 unknown user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from vlan interface
Jan 1 01:01:12 unknown user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from master interface
Jan 1 01:01:12 unknown user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from vlan interface
Jan 1 01:01:12 unknown user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from master interface
Jan 1 01:01:12 unknown user.warn kernel: vlan2: Setting MAC address to 08 60 6e bb 7f e1.
Jan 1 01:01:12 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:01:12 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:01:14 unknown user.info redial[973]: Started. Time: 10
Jan 1 01:01:14 unknown daemon.notice pppd[972]: pppd 2.4.5 started by root, uid 0
Jan 1 01:01:14 unknown user.notice root: 3G MODEM already found - using option module
Jan 1 01:01:20 unknown daemon.err nmbd[794]: Samba server UNKNOWN is now a domain master browser for workgroup WORKGROUP on subnet 192.168.1.2
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPDISCOVER(br0) f0:4f:7c:ba:de:52
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPOFFER(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPREQUEST(br0) 192.168.1.34 ac:72:89:c3:cc:10
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPACK(br0) 192.168.1.34 ac:72:89:c3:cc:10 JA-Komputer
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPDISCOVER(br0) f0:4f:7c:ba:de:52
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPOFFER(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPREQUEST(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:21 unknown daemon.info dnsmasq-dhcp[839]: DHCPACK(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:22 unknown user.notice root: Transmission daemon successfully started
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: Transmission 2.77 (14031) started (session.c:722)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: RPC Server Adding address to whitelist: 127.0.0.1 (rpc-server.c:803)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: RPC Server Serving RPC and Web requests on port 127.0.0.1:9091/transmission/ (rpc-server.c:997)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: RPC Server Whitelist enabled (rpc-server.c:1001)
Jan 1 01:01:24 unknown daemon.err transmission-daemon[1090]: UDP Failed to set receive buffer: requested 4194304, got 225280 (tr-udp.c:77)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: UDP Please add the line "net.core.rmem_max = 4194304" to /etc/sysctl.conf (tr-udp.c:82)
Jan 1 01:01:24 unknown daemon.err transmission-daemon[1090]: UDP Failed to set send buffer: requested 1048576, got 225280 (tr-udp.c:88)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: UDP Please add the line "net.core.wmem_max = 1048576" to /etc/sysctl.conf (tr-udp.c:93)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: DHT Generating new id (tr-dht.c:309)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: Using settings from "/tmp/mnt/sdb1/torrent/.settings" (daemon.c:517)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: Saved "/tmp/mnt/sdb1/torrent/.settings/settings.json" (bencode.c:1738)
Jan 1 01:01:24 unknown daemon.info transmission-daemon[1090]: Port Forwarding Not forwarded (port-forwarding.c:93)
Jan 1 01:01:33 unknown daemon.info dnsmasq-dhcp[839]: DHCPDISCOVER(br0) f0:4f:7c:ba:de:52
Jan 1 01:01:33 unknown daemon.info dnsmasq-dhcp[839]: DHCPOFFER(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:33 unknown daemon.info dnsmasq-dhcp[839]: DHCPREQUEST(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:33 unknown daemon.info dnsmasq-dhcp[839]: DHCPACK(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:34 unknown user.info redial[973]: WAN down. Reconnecting...
Jan 1 01:01:34 unknown daemon.info dnsmasq[839]: exiting on receipt of SIGTERM
Jan 1 01:01:34 unknown user.debug init[1]: 182: pptp peerdns disabled
Jan 1 01:01:34 unknown daemon.info dnsmasq[1158]: started, version UNKNOWN cachesize 1500
Jan 1 01:01:34 unknown daemon.info dnsmasq[1158]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack Tomato-helper auth
Jan 1 01:01:34 unknown daemon.info dnsmasq[1158]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 01:01:34 unknown daemon.info dnsmasq-dhcp[1158]: DHCP, IP range 192.168.1.3 -- 192.168.1.51, lease time 1d
Jan 1 01:01:34 unknown daemon.warn dnsmasq[1158]: no servers found in /etc/resolv.dnsmasq, will retry
Jan 1 01:01:34 unknown daemon.info dnsmasq[1158]: read /etc/hosts - 2 addresses
Jan 1 01:01:34 unknown daemon.info dnsmasq[1158]: read /etc/dnsmasq/hosts/hosts - 4 addresses
Jan 1 01:01:34 unknown daemon.info dnsmasq-dhcp[1158]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 01:01:34 unknown daemon.warn pppd[972]: Child process /usr/sbin/chat -V -t 60 -f /tmp/ppp/connect.chat (pid 1005) terminated with signal 15
Jan 1 01:01:34 unknown daemon.err pppd[972]: Connect script failed
Jan 1 01:01:34 unknown local2.err chat[1006]: SIGTERM
Jan 1 01:01:34 unknown daemon.err nmbd[794]: Samba name server UNKNOWN is now a local master browser for workgroup WORKGROUP on subnet 192.168.1.2
Jan 1 01:01:35 unknown daemon.info pppd[972]: Exit.
Jan 1 01:01:35 unknown user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from vlan interface
Jan 1 01:01:35 unknown user.debug kernel: vlan2: del 33:33:00:00:00:01 mcast address from master interface
Jan 1 01:01:35 unknown user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from vlan interface
Jan 1 01:01:35 unknown user.debug kernel: vlan2: del 01:00:5e:00:00:01 mcast address from master interface
Jan 1 01:01:35 unknown user.warn kernel: vlan2: Setting MAC address to 08 60 6e bb 7f e1.
Jan 1 01:01:35 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:01:35 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:01:37 unknown daemon.notice pppd[1224]: pppd 2.4.5 started by root, uid 0
Jan 1 01:01:37 unknown user.info redial[1225]: Started. Time: 10
Jan 1 01:01:38 unknown user.notice root: 3G MODEM already found - using option module
Jan 1 01:01:46 unknown daemon.info dnsmasq-dhcp[1158]: DHCPDISCOVER(br0) f0:4f:7c:ba:de:52
Jan 1 01:01:46 unknown daemon.info dnsmasq-dhcp[1158]: DHCPOFFER(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:46 unknown daemon.info dnsmasq-dhcp[1158]: DHCPREQUEST(br0) 192.168.1.16 f0:4f:7c:ba:de:52
Jan 1 01:01:46 unknown daemon.info dnsmasq-dhcp[1158]: DHCPACK(br0) 192.168.1.16 f0:4f:7c:ba:de:52
btw. mam w domu jeszcze inny modem - huawei e3131, tyle że to wersja Hi-Link (czyli, że działa na zasadzie karty sieciowej a nie jak modem).Więc kombinuję z tym e169
Edytowany przez lew487 dnia 13-08-2013 17:04
' target='_blank'>Link
No bądźmy poważni 
dev/ttyUSB0 (tego ustawienia nie jestem pewny, bo mam 2 porty usb i nie wiem jak sprawdzić, który to)
