Ogółem głosów: 416
Musisz zalogować się, aby móc zagłosować. Rozpoczęto: 02/02/2015 09:38
Twoje IP
18.218.61.16
Tomato 1.0
Po paru tygodniach przerwy między ostatnim wydaniem, do działu Download trafiły najnowsze paczki firmware Tomato 1.0. Lista poprawionych błędów, dodanych nowych opcji jest imponująca i świadczy o tym że Jonathan Zarate (Tofu) rozpędził się z Tomato na całego. Firmware do zassania z działu Download.
Changelog
Version 1.00
* Fixed "all day" restrictions always blocks regardless of the day of week setting.
* Fixed several problems with the Basic Networking page.
* Fixed a problem with WRT54G v1 that may have caused problems with WDS.
* Fixed PPPoE timer may not reset.
* Fixed DHCP client may not renew when used with some ISPs.
* Fixed a memory leak in UPNP.
* Added support for Buffalo WHR-G54S/WHR-HP-G54S.
* Added a real-time (well, almost) bandwidth monitor. This functions a little differently in that you can use it without the rstats program and data is pulled and stored via JavaScript on demand. Since this doesn't run all the time, the initial 5 minutes (@ 60s avg - it will look flat) of data is taken from rstats if available.
* Added a chart for bandwidth distribution per QOS class (outbound).
* Added an Expire Early button in Advanced/CT to flush conntrack of connections that are idle for more than 15 seconds (for debugging).
* Added an "all computers except the following" option in Access Restriction. Keep in mind that this is not the same as an "allow". Even if a computer is exempted from one restriction, it's still checked for other restrictions.
* Added an option to block wireless access to the GUI. Note - This will only work if the client is connected directly.
* Added an option to change the color scheme for the GUI.
* Added a backup/restore, "first day of the month" option, and "excluded interface" option In Bandwidth Monitor. All interfaces that produce stats (except loopback) are now shown unless excluded.
* Enabled support for mixed WPA/WPA2.
* Resetting of classification when changing QOS settings is now optional. If enabled, it's now instant and will reset even idle connections.
* /jffs2 has been renamed to /jffs, and /misc to /rom. If you have scripts that use these, don't forget to change them.
* Upgraded busybox to 1.2.2, dnsmasq to 2.35.
* Other minor/internal changes and code cleanup.
fachowcy będą mówić o jakichś cudach, wielkościach skryptów bla bla bla...a ja powiem, że pomidorek jest po prostu ładny ostatecznie zdecydowałem się na przejście z thibora na pomidora. polecam !! B)
WAN (vlan1) to siec internet np. z modemu
WL (eth1) to sama siec bezprzewodowa
br0 to caly transfer co przechodzi przez router
eth0 router ale bez wifi
vlan0 sam lan
· Łącznie użytkowników: 24,117 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
tamtosiamto
31-03-2024 12:54
Wesolego jajka wszytskim forumowiczom
tamtosiamto
28-03-2024 23:24
tak, tak zgadza sie, ale ja pytam o wykluczenie noda na guest network w first set, i to nie dziala
Adooni
24-03-2024 13:16
Guest network is currently designed to allow the first set of each band (2.4G, 5G, 5G-1) available to the AiMesh node
tamtosiamto
24-03-2024 03:03
ale w 1 jest opcja do wyboru - dla calej sieci albo rutera only i wlasnie o tym mowie, ze nie dziala
Adooni
23-03-2024 16:31
w dokumencie asusa jest ze wlasnie dla 1 ma dzialac na nodach tez
tamtosiamto
23-03-2024 15:39
tak, ale nie zmienia to faktu, ze w pierwszej nie dziala wylaczanie aimesh dla goscinnej( a powinno), czyli jest jakis bug. Mam start soft, bo to dsl-ac68 ktory nie jest juz updateowany
Adooni
22-03-2024 18:07
nie, 1 wsza bedzie wszedzie trzeba 2ga zrobic dla kazdego pasma te nie sa przenoszone
tamtosiamto
19-03-2024 19:57
czyli jak mam jedna siec goscinna to powinno dzialac separowanie gosci od noda -a nie dziala
tamtosiamto
19-03-2024 19:50
@Adooni 'Only one set is available for 1 band' i tak mam-1 set dla 2.4ghz i 1 dla 5ghz-czy czegos nie rozumiemW drugiej sieci goscinnej nie ma opcji wyboru Ruter only/ All nodes
Adooni
19-03-2024 19:14
no to przeczytaj to 2 pod - 1 stet z kazdego pasma jest dopuszczony na nody. zrob 2 siec jako goscinna na danym pasmie i wtedy sprawdz
w 05 grudnia 2006 14:47:01
w 06 grudnia 2006 07:54:18
w 06 grudnia 2006 10:21:40
w 10 grudnia 2006 14:52:35