witam
po długiej walce odało mi się uruchomić modem lte z Play Huawei e3372 na Netgear 3500l v2 -tomato 1,23......
Jak tego dokonałeś z modemem nie HILINK???
Poradnik z pierwszej strony tego tematu nie działa ? Napisz co zrobiłeś i w którym miejscu nie działa Tylko tym sposobem możemy sprawdzić gdzie leży problem.
walka była na modemie z playa .Trzeba zwrócić uwage jakie ethprzypisze sobie router dla modemu. reszte postepowałęm zgodnie z instrukcja z pierwszej strony i jak pamietam modem byl przypoisany do usb01.
W tej chwili mam modem z sieci IMT sprzedawany na allegro i pomógł ten post w jego uruchomieniu.https://openlinksys.info/forum/viewthread.php?thread_id=18569.
Rożnica jest taka ,że na PLayowym modemie uzyskiwałem 20/7 mb/s a teraz największa to 48/20.
Zastanawiam się tylko jak skonfigurować router aby kozystać jednocześnie z nerwostrady i lte (nerwostrade mam do sierpnia) a jeśli to mozliwe nie chce uszczuplac pakietu z lte
Router to
Netgear 3500l v2
PS . z nerwostrady jest osobny router
Witam.
Mam problem z podłączeniem modemu E3272 hilink do RT-N16 tomato-K26USB-1.28.RT-MIPSR2-123-AIO. W tomato mam ustawione na 3G Modem, ttyUSB0. W modemie nie zmieniałęm IP i jest standardowo 192.168.1.1 Czy mógłby ktoś łopatologicznie wytłumaczyć jak się ładuje moduły, próbowałem z tutka z https://openlinksys.info/forum/viewthread.php?thread_id=15390&rowstart=0 ale nie wiem czy trzeba ładować wszystkie 3 czy tylko cdc_ether.ko i co dalej. Dochodzę to komendy MODE="AT^NDISDUP=1,1,\"internet\"" gcom -d /dev/ttyUSB0 -s /etc/gcom/setmode.gcom wyrzuca:
Trying to set mode
Timeout setting WWAN mode!
I dalej nie wiem co robić.
Po wpisaniu dmesg wyrzuca: rd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 pkg 10 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126576k/131068k available (33k kernel code, 4340k reserved, 2893k data, 116k init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x01fe0000 : "linux"
0x00135000-0x00f20000 : "rootfs"
0x00f20000-0x01fe0000 : "jffs2"
0x01fe0000-0x02000000 : "nvram"
Found a 0MB serial flash
sflash: found no supported devices
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Oct 14 2014 16:42:49]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Warning: unable to open an initial console.
emf: module license 'Proprietary' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.147.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.147.0
Algorithmics/MIPS FPU Emulator v1.5
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: dev_set_allmulti(master, 1)
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering forwarding state
br0: port 1(vlan1) entering forwarding state
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbserial_generic 1-1:1.0: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 1-1:1.0 failed with error -5
usbserial_generic 1-1:1.1: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
usb 1-1: USB disconnect, address 2
generic ttyUSB0: generic converter now disconnected from ttyUSB0
usbserial_generic 1-1:1.1: device disconnected
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb 1-1: USB disconnect, address 3
usb 1-1: new high speed USB device using ehci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbserial_generic 1-1:1.0: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 1-1:1.0 failed with error -5
usbserial_generic 1-1:1.1: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
usb 1-2: new high speed USB device using ehci_hcd and address 5
usb 1-2: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
scsi 1:0:0:0: Direct-Access General UDisk 5.00 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 7864320 512-byte hardware sectors (4027 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 1:0:0:0: [sda] Attached SCSI removable disk
cdc_ncm: 14-Mar-2012
usbcore: registered new interface driver cdc_ncm
usb 1-1: USB disconnect, address 4
generic ttyUSB0: generic converter now disconnected from ttyUSB0
usbserial_generic 1-1:1.1: device disconnected
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usb 1-1: new high speed USB device using ehci_hcd and address 6
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb 1-1: USB disconnect, address 6
usb 1-1: new high speed USB device using ehci_hcd and address 7
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbserial_generic 1-1:1.0: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 1-1:1.0 failed with error -5
usbserial_generic 1-1:1.1: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
cdc_ether: probe of 1-1:1.0 failed with error -16
usbcore: registered new interface driver cdc_ether
Może ktoś pomoże jak to skonfigurowąć żeby działało.
Połączony z 01 December 2014 09:42:10:
Ok, poradziłem sobie, zainstalowałem oryginalne oprogramowanie Asusa i samo się połączyło, Down: 40Mb Up. 20Mb.
Edytowany przez malina dnia 01-12-2014 09:42
Czy jest jakaś możliwość sprawdzenia parametrów połączenia modemu (nie hilink) czyli Rssi itd? bo w webui nie ma takiej opcji, a troche to utrudnia dobre ustawienie (lokacyjne) modemu :-)
Połączony z 14 December 2014 22:36:51:
W sumie to chciałbym uzyskać właśnie wynik podobny do podłączenia serial do modemu w trakcie połączenia, tak jak tutaj:
https://openlinksys.info/forum/viewthread.php?thread_id=15811&rowstart=160#post_138428
Jak wiec polaczyc sie w trybie 'serial' przez np. ssh :-)? da sie?
Też się przyłączam do pytania. Jaki na dzień dzisiejszy jest najbardziej odpowiedni modem LTE aby w Tomato został automatycznie wykryty i działał bez żadnych poważnych "kombinacji". Mój FW- Tomato Firmware 1.28.0000 MIPSR2-124 K26 USB BTgui-VPN
Działa w sensie komend ale wyświetla mi Błąd
comgt 17:29:00 -> -- Error Report --
comgt 17:29:00 -> ----> ^
comgt 17:29:00 -> Error @224, line 13, String is shorter than second argument. (7)
po przełączeniu modemu w tryb RAS za pomocą skrypty switch3g (odpala się automatycznie gdy wybierasz połączenie 3G Modem, pojawią ci się nowe interfejsy /dev/ttyUSB
Jeden z nich będzie twoim interfejsem diagnostycznym, czyli takim, za pomocą którego będziesz mógł komunikować się z modemem. Przykładowo w moim e3276 mogę komunikować się za pomocą /dev/ttyUSB1.
Oto kilka przykładów:
Cytat
root@unknown:/tmp/home/root# gcom -d /dev/ttyUSB1 reg
Waiting for Registration
Registered on Home network: "Plus",7
root@unknown:/tmp/home/root# gcom -d /dev/ttyUSB1 sig
Signal Quality: 21,99
root@unknown:/tmp/home/root# gcom -d /dev/ttyUSB1 info
##### Wireless WAN Modem Configuration #####
Product text:
====
Manufacturer: huawei
Model: E3276
Revision: 21.430.03.04.55
IMEI: 863781018485079
+GCAP: +CGSM,+DS,+ES
OK
====
Manufacturer: huawei
IMEI and Serial Number: 863781018485079
Manufacturer's Revision:
21.430.03.04.
Hardware Revision:
Network Locked: ERROR:
Customisation:
Band settings: (
)
APN: 0,"IP","","",0,0,0,0
##### END #####
Proxmox VE:i5-13400T, 64GB RAM, 2x 512GB NVMe, 3x 2TB SSD, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology SA6400 VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
Czy ktoś byłby tak łaskawy pomóc mi ogarnąć ten cholerny router i modem? Już powoli nie daję rady..
Pacjent Netgear 3500L v1 z tomato 191
Model Huawei E3273 bez Hilink, wersja softu:
root@robhome:/tmp/home/root# gcom -d /dev/ttyUSB1 info
##### Wireless WAN Modem Configuration #####
Product text:
====
huawei
Model: E3272
Revision: 21.436.11.01.209
IMEI: 864217020536822
+GCAP: +CGSM,+DS,+ES
OK
====
Manufacturer:
IMEI and Serial Number:
Manufacturer's Revision: comgt 16:43:23 -> -- Error Report --
comgt 16:43:23 -> ----> ^
comgt 16:43:23 -> Error @982, line 56, String is shorter than second argument. (7)
Aktualnie model się łączy skryptem w Init:
switch3g
sleep 3
modprobe cdc_ncm
sleep 10
MODE="AT^NDISDUP=1,1,\"internet\"" gcom -d /dev/ttyUSB0 -s /etc/gcom/setmode.gcom
sleep 3
service wan restart
dmesg pokazuje:
root@robhome:/tmp/home/root# dmesg
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #15 Sat Oct 4 15:53:10 CEST 2014
CPU revision is: 00019740
Found a 8MB ST compatible serial flash
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM4716 rev 1 pkg 10 at 453 MHz
Using 226.500 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61860k/65536k available (33k kernel code, 3612k reserved, 2726k data, 116k init, 0k highmem)
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Disabled
PCI: Fixing up bus 0
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Creating 6 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x00790000 : "linux"
0x00127c00-0x00760000 : "rootfs"
0x00760000-0x00780000 : "jffs2"
0x007f0000-0x00800000 : "nvram"
0x007e0000-0x007f0000 : "board_data"
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Oct 4 2014 15:38:54]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Warning: unable to open an initial console.
emf: module license 'Proprietary' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.147.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.147.0
Algorithmics/MIPS FPU Emulator v1.5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
usblp: USB Printer Device Class driver
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new high speed USB device using ehci_hcd and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb 1-1.2: new high speed USB device using ehci_hcd and address 4
usb 1-1.2: configuration #1 chosen from 1 choice
hub 1-1.2:1.0: USB hub found
hub 1-1.2:1.0: 4 ports detected
usb 1-1.3: new high speed USB device using ehci_hcd and address 5
usb 1-1.3: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
usb 1-1.3: USB disconnect, address 5
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usb 1-1.3: new high speed USB device using ehci_hcd and address 6
usb 1-1.3: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: dev_set_allmulti(master, 1)
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering forwarding state
br0: port 1(vlan1) entering forwarding state
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 3934208 512-byte hardware sectors (2014 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdb] Attached SCSI removable disk
usbcore: deregistering interface driver sierra
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver Sierra USB modem
usbcore: deregistering interface driver option
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver GSM modem (1-port)
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: deregistering interface driver cdc_acm
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbserial_generic 1-1.3:1.0: generic converter detected
usb 1-1.3: generic converter now attached to ttyUSB0
usbserial_generic 1-1.3:1.1: generic converter detected
usb 1-1.3: generic converter now attached to ttyUSB1
usbserial_generic 1-1.3:1.2: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 1-1.3:1.2 failed with error -5
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
cdc_ncm: 14-Mar-2012
usb 1-1.3: MAC-Address: 0c:5b:8f:27:9a:64
usb0: register 'cdc_ncm' at usb-0000:00:04.1-1.3, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
usbcore: registered new interface driver cdc_ncm
EXT3-fs: starting recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
ADDRCONF(NETDEV_UP): usb0: link is not ready
HTB: quantum of class 20010 is small. Consider r2q change.
HTB: quantum of class 20011 is small. Consider r2q change.
Problem jest taki że modem łączy się po HSPA+ zamiast LTE.
· Łącznie użytkowników: 24,115 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Maniek91PL
06-11-2024 22:37
dzięki !
maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia
Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa
overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.
maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.
overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?
maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach
maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności", więc prawdopodobnie gdzieś przepięcie.
servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.
maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
' target='_blank'>Link
