BusyBox v1.00 (2007.01.30-11:42+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.



  _______                     ________        __

 |       |.-----.-----.-----.|  |  |  |.----.|  |_

 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|

 |_______||   __|_____|__|__||________||__|  |____|

          |__| W I R E L E S S   F R E E D O M

 WHITE RUSSIAN (0.9) -------------------------------

  * 2 oz Vodka   Mix the Vodka and Kahlua together

  * 1 oz Kahlua  over ice, then float the cream or

  * 1/2oz cream  milk on the top.

 ---------------------------------------------------

root@OpenWrt:~# dmesg

CPU revision is: 00029006

Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 16kB, 2-way, linesize 16 bytes.

Linux version 2.4.30 (nbd@ds10) (gcc version 3.4.4 (OpenWrt-1.0)) #1 Sat Feb 3 13:16:08 CET 2007

Setting the PFC value as 0x15

Determined physical RAM map:

 memory: 02000000 @ 00000000 (usable)

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200

CPU: BCM4704 rev 9 at 264 MHz

Using 132.000 MHz high precision timer.

Calibrating delay loop... 263.78 BogoMIPS

Memory: 30436k/32768k available (1455k kernel code, 2332k reserved, 104k data, 80k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

Checking for 'wait' instruction...  unavailable.

POSIX conformance testing by UNIFIX

PCI: Fixing up bus 0

PCI: Fixing up bridge

PCI: Setting latency timer of device 01:00.0 to 64

PCI: Fixing up bus 1

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

Registering mini_fo version $Id$

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.

Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher

pty: 256 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled

ttyS00 at 0xb8000300 (irq = 3) is a 16550A

ttyS01 at 0xb8000400 (irq = 0) is a 16550A

b44.c:v0.93 (Mar, 2004)

PCI: Setting latency timer of device 00:01.0 to 64

eth0: Broadcom 47xx 10/100BaseT Ethernet 00:18:f3:3b:6a:79

PCI: Setting latency timer of device 00:02.0 to 64

eth1: Broadcom 47xx 10/100BaseT Ethernet 40:10:18:00:00:2d

Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0

Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0

Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0

 Amd/Fujitsu Extended Query Table v1.3 at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling fast programming due to code brokenness.

Flash device: 0x800000 at 0x1c000000

bootloader size: 262144

Physically mapped flash: Filesystem type: squashfs, size=0xfb158

Creating 5 MTD partitions on "Physically mapped flash":

0x00000000-0x00040000 : "cfe"

0x00040000-0x007f0000 : "linux"

0x000be400-0x001c0000 : "rootfs"

mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only

0x007f0000-0x00800000 : "nvram"

0x001c0000-0x007f0000 : "OpenWrt"

Initializing Cryptographic API

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

ip_conntrack version 2.1 (5953 buckets, 5953 max) - 332 bytes per conntrack

ip_tables: (C) 2000-2002 Netfilter core team

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NET4: Ethernet Bridge 008 for NET4.0

802.1Q VLAN Support v1.8 Ben Greear 

All bugs added by David S. Miller 

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 80k freed

Algorithmics/MIPS FPU Emulator v1.5

diag: Detected 'ASUS WL-500g Premium'

Probing device eth0: found!

b44: eth0: Link is up at 100 Mbps, full duplex.

b44: eth0: Flow control is off for TX and off for RX.

mini_fo: using base directory: /

mini_fo: using storage directory: /jffs

jffs2.bbc: SIZE compression mode activated.

PCI: Setting latency timer of device 01:02.0 to 64

PCI: Enabling device 01:02.0 (0004 -> 0006)

eth2: Broadcom BCM4318 802.11 Wireless Controller 3.90.37.0

Journalled Block Device driver loaded

BFL_ENETADM not set in boardflags. Use force=1 to ignore.

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb.c: registered new driver acm

acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters

PCI: Setting latency timer of device 00:03.0 to 64

usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6

usb-ohci.c: usb-00:03.0, PCI device 14e4:4715

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 2 ports detected

usb.c: registered new driver serial

usbserial.c: USB Serial support registered for Generic

usbserial.c: USB Serial Driver core v1.4

SCSI subsystem driver Revision: 1.00

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

USB Mass Storage support registered.

uhci.c: USB Universal Host Controller Interface driver v1.1

PCI: Enabling device 01:03.0 (0000 -> 0001)

uhci.c: USB UHCI at I/O 0x100, IRQ 2

usb.c: new USB bus registered, assigned bus number 2

hub.c: USB hub found

hub.c: 2 ports detected

PCI: Enabling device 01:03.1 (0000 -> 0001)

uhci.c: USB UHCI at I/O 0x120, IRQ 2

usb.c: new USB bus registered, assigned bus number 3

hub.c: USB hub found

hub.c: 2 ports detected

PCI: Enabling device 01:03.2 (0000 -> 0002)

ehci_hcd 01:03.2: PCI device 1106:3104

ehci_hcd 01:03.2: irq 2, pci mem c01ea000

usb.c: new USB bus registered, assigned bus number 4

EHCI: Enabling VIA 6212 workarounds

ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4

hub.c: USB hub found

hub.c: 4 ports detected

usbserial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter

belkin_sa.c: USB Belkin Serial converter driver v1.2

usbserial.c: USB Serial support registered for FTDI SIO

usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible

usbserial.c: USB Serial support registered for FTDI FT232BM Compatible

usbserial.c: USB Serial support registered for USB-UIRT Infrared Tranceiver

usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver

ftdi_sio.c: v1.3.5:USB FTDI Serial Converters Driver

usbserial.c: USB Serial support registered for MCT U232

mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0

usbserial.c: USB Serial support registered for PL-2303

pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.11

hub.c: connect-debounce failed, port 1 disabled

usbserial.c: USB Serial support registered for Handspring Visor / Treo / Palm 4.0 / Clié 4.x

usbserial.c: USB Serial support registered for Sony Clié 3.5

usbserial.c: USB Serial support registered for Sony Clié 5.0

visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Clié driver v1.7

device eth0 entered promiscuous mode

hub.c: new USB device 01:03.0-1, assigned address 2

usb.c: USB device 2 (vend/prod 0x483/0x7554) is not claimed by any active driver.

b44: eth0: Link is up at 100 Mbps, full duplex.

b44: eth0: Flow control is off for TX and off for RX.

vlan0: add 01:00:5e:00:00:01 mcast address to master interface

vlan0: dev_set_promiscuity(master, 1)

vlan0: dev_set_allmulti(master, 1)

device eth2 entered promiscuous mode

eth2: attempt to add interface with same source address.

br0: port 2(eth2) entering listening state

br0: port 1(vlan0) entering listening state

br0: port 2(eth2) entering learning state

br0: port 1(vlan0) entering learning state

br0: port 2(eth2) entering forwarding state

br0: topology change detected, propagating

br0: port 1(vlan0) entering forwarding state

br0: topology change detected, propagating

vlan1: add 01:00:5e:00:00:01 mcast address to master interface

root@OpenWrt:~#