19 Września 2024 23:36:24
Nawigacja
· Strona Główna
· Forum

· Tomato by Shibby
· FreshTomato


Wątki na forum
Najnowsze dyskusje
· Asus AC-3200 aktuali...
· [MOD] FreshTomato-AR...
· [S] i7-7700T + płyta
· RT AX 89X
· Wireguard na FreshTo...
· [MOD] FreshTomato-MI...
· Jaki router kupić?
· Openvpn+klient android
· Bandwidth -Dzienne M...
· TOMATO VPN GUI - kon...
· [MOD] Tomato64 (x86-64)
· Jaki router do 1000/...
· [S] ASUS RT-AX89X
· Czy to jeszcze NAS?
· Switch zasilany prze...
· [Howto] Xpenology na...
· Asus TUF-AX3000_V2 p...
· Kto "steruje" MAC ad...
· Omv raid 0
· [S] Orange Pi Lite
Najpopularniejsze obecnie wątki
· [MOD] FreshTomato... [904]
· Asus AC-3200 aktu... [2]
Ankieta
Jaki procesor posiada twój router?

Broadcom MIPSEL
Broadcom MIPSEL
36% [151 głosów]

Broadcom ARM
Broadcom ARM
52% [217 głosów]

Atheros
Atheros
5% [22 głosów]

Marvell
Marvell
1% [4 głosów]

Ralink
Ralink
1% [3 głosów]

Intel/AMD/VIA
Intel/AMD/VIA
1% [5 głosów]

Żaden z powyższych
Żaden z powyższych
4% [15 głosów]

Ogółem głosów: 417
Musisz zalogować się, aby móc zagłosować.
Rozpoczęto: 02/02/2015 09:38
Twoje IP
3.145.85.151
Zobacz wątek
OpenLinksys » :: OPROGRAMOWANIE :: » DD-WRT - firmware
 Drukuj wątek
Outdoorowy CPE na Atherosie - problem z DD-WRT
iplab
Panowie proszę o pomoc w uruchomieniu DD-WRT na PCBA Abocom W2101 - AR2317 4MB Flash / 16MB mem / 1ETH. Do uruchomienia używam DD-WRT przygotowanego pod DIR-300.

Wg zeznań ludzi z forum uruchomili oni na tej platformie DD-WRT http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51465&highlight=abocom

Próbowałem z oryginalnym RedBootem wgrać tylko linux.bin - przy próbie uruchomienia wywala krzaki. Następnie przeszedłem przez całą procedurę dla DIR-300, łącznei z podmianą RedBoota. Problem pozostał.

Poniżej zrzuty z logu konsoli


Now booting linux kernel:
 Base address 0x80030000 Entry 0x80041000
 Cmdline :


a następnie:


ş§ŔD2ĹÜň°°° °°0ůŕá`áT°0Ĺú`ĂúĆŔ`ăĐ]
FIĹÜň°0° °°0ů
wgę=÷ńDrŔY{YÉ9pąŔŘđ°úi9öز#zs:20eÜ9ČĘjxŘű8]ËâŕdČĘč;(ňúň22ńp}ČĘč;(20ň22ąp}Čʨ
8:x2ypňńńYÓŔ\`słz`i=Üň(z˛0ćŔÔ2y`bg0°


Walczę z tematem już trzeci dzień - proszę o pomoc w uruchomieniu DD-WRT na tym hardware.

Zrzut z konsoli dla oryginalnego firmware:

Cytat


+phyAddr=8 phyID1=0x4d phyId2=0xd021.
Ethernet eth0: MAC address 00:12:0e:b5:29:8a
IP: 192.168.1.20/255.255.255.0, Gateway: 192.168.1.1
Default server: 192.168.1.209

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version UNKNOWN - built 13:56:23, Dec 6 2007

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: ap61
RAM: 0x80000000-0x81000000, [0x8003fe00-0x80fe1000] available
FLASH: 0xbfc00000 - 0xbfff0000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 1.000 seconds - enter ^C to abort
^C
RedBoot> fis list
Name FLASH addr Mem addr Length Entry point
RedBoot 0xBFC00000 0xBFC00000 0x00030000 0x80040000
rootfs 0xBFC30000 0xBFC30000 0x00300000 0x00000000
web 0xBFF30000 0xBFF30000 0x00010000 0x00000000
vmlinux.bin.l7 0xBFF40000 0x80041000 0x00090000 0x801EC040
cfg 0xBFFD0000 0xBFFD0000 0x00010000 0x0AD50057
FIS directory 0xBFFE0000 0xBFFE0000 0x0000F000 0x00000000
RedBoot config 0xBFFEF000 0xBFFEF000 0x00001000 0x00000000
RedBoot>



+phyAddr=8 phyID1=0x4d phyId2=0xd021.
Ethernet eth0: MAC address 00:12:0e:b5:29:8a
IP: 192.168.1.20/255.255.255.0, Gateway: 192.168.1.1
Default server: 192.168.1.209

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version UNKNOWN - built 13:56:23, Dec 6 2007

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: ap61
RAM: 0x80000000-0x81000000, [0x8003fe00-0x80fe1000] available
FLASH: 0xbfc00000 - 0xbfff0000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -l vmlinux.bin.l7
Image loaded from 0x80041000-0x80220000
RedBoot> go
řřxxxxxxxxřxřxxřxřxřxxřxxřxxřřxxřxxřxřřxxxxxřxřxxřxxx
xxřxřxřxřxřxxxřxxxxřřxxxxxřxxxřxxxřxřxxřxxxxxxxxřxxřř
xxxxřxřxřxxxxřxřxxxxřxxřxxxxxxxřxxřxřřxxxxxxřxxřxxxřx
xxxřřxxxřxxřřxxxxřxřxřxxxxřxřxxxxřxxřxxxxxxxřxřxřxxxx
řxxxxxřxřxřxxřxxřxxxxxxxřxxřxxxřřxxřxřxřxxxřxxxřxxxřx
řxřxxxxxxřxxxřxxxxxřxřxřxřxřxřxxřxřřxřřřxxřřxřřxxřřxx
xxxxřxxxřxxxxřřxřxřxxxxxřxxxřxxxřxxxxřxxřxxxřxxřxřxxx
řřxřxxxřxxxxřxxxxřxxxxxxřřxřxřxřxxxxřxřxřxxřxxxxxxxřř
xřxxřřxřxřxxxxxxřřxřxxxxxxxxxřřxřxřxxxxxxxřxxxxxxxxxř
řxřxřxxxxxxřxxxxxxxxxřřxxxxxřxxxřxřxřxřřxřřxxřxxřxřxř
xxxřřxřxřxxřxřxxxřřxřxxxxřřxxřxxxxřxřxxxxxxxřxřxřxxřx
xxxxxřxxřxřxřxřxřxřřxxxxx
<4>Calibrating delay loop... 183.50 BogoMIPS
<6>Memory: 13844k/16384k available (1693k kernel code, 2540k reserved, 124k data, 72k init, 0k highmem)
<6>Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
<6>Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
<4>Checking for 'wait' instruction... unavailable.
<4>POSIX conformance testing by UNIFIX
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<6>squashfs: version 3.1 (2006/08/19) Phillip Lougher
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with no serial options enabled
<6>ttyS00 at 0xb1100003 (irq = 37) is a 16550A
<6>Generic MIPS RTC Driver v1.0
<4>WatchDog driver for ar531x.
<4>Switch driver for ar531x.
<4>register gpio interrupt 2: gpio 1
<6>PPP generic driver version 2.4.2
<6>PPP Deflate Compression module registered
<6>PPP BSD Compression module registered
<4>MTD driver for SPI flash.
<4>spiflash: Probing for Serial flash ...
<4>spiflash: Found SPI serial Flash.
<4>4194304: size
<5>Creating 6 MTD partitions on "spiflash":
<5>0x00030000-0x00330000 : "rootfs"
<5>0x00330000-0x00340000 : "web"
<5>0x00340000-0x003d0000 : "vmlinux.bin.l7"
<5>0x003d0000-0x003e0000 : "cfg"
<5>0x003e0000-0x003f0000 : "FIS+RedBoot Config"
<5>0x003f0000-0x00400000 : "HW&RF Config"
<4>init_mtdchar: Entering Write Page mode
<6>ath_hal: 0.9.17.1 (AR5212, AR5312, RF5111, RF5112, RF2413, RF5413, RF2317)
<6>ath_ahb: 0.9.4.5 (Atheros/multi-bss)
<4>wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
<4>wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
<4>wifi0: mac 11.0 phy 4.8 radio 8.6
<4>wifi0: Use hw queue 1 for WME_AC_BE traffic
<4>wifi0: Use hw queue 0 for WME_AC_BK traffic
<4>wifi0: Use hw queue 2 for WME_AC_VI traffic
<4>wifi0: Use hw queue 3 for WME_AC_VO traffic
<4>wifi0: Use hw queue 8 for CAB traffic
<4>wifi0: Use hw queue 9 for beacons
<6>wifi0: Atheros 2317 WiSoC: mem=0xb0000000, irq=3
<6>ath_rate_atheros: Version 2.0.1
<4>Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
<6>Initializing Cryptographic API
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<6>IP: routing cache hash table of 512 buckets, 4Kbytes
<6>TCP: Hash tables configured (established 1024 bind 2048)
<4>ip_conntrack version 2.1 (128 buckets, 1024 max) - 304 bytes per conntrack
<4>ip_conntrack_pptp version 1.9 loaded
<4>ip_tables: (C) 2000-2002 Netfilter core team
<6>ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<6>NET4: Ethernet Bridge 008 for NET4.0
<6>wlan: 0.8.4.2 (Atheros/multi-bss)
<6>wlan: mac acl policy registered
<6>wlan: cal client addresses list registered
<4>VFS: Mounted root (squashfs filesystem) readonly.
<6>Freeing unused kernel memory: 72k freed
<4>Algorithmics/MIPS FPU Emulator v1.5
<4>register gpio interrupt 1: gpio 6
AP MODE !!!
AP MODE !!!!!!!
wlanconfig
wlanconfig.0
wlanconfig.0.0
ap_service
AP MODE !!!
<6>device eth0 entered promiscuous mode

<6>device ath0 entered promiscuous mode
<6>br0: port 2(ath0) entering learning state
<6>br0: port 1(eth0) entering learning state
Updating neighbor's ARP cache ...
<6>br0: port 2(ath0) entering forwarding state
<6>br0: topology change detected, propagating
<6>br0: port 1(eth0) entering forwarding state
<6>br0: topology change detected, propagating

Start webs& ^_^

Steve Test:userName=admin,userPass=
[webs] initWebs completed
udhcp server (v0.9.9-pre) started


AP MODE !!!!!!!





Steve Test 600


BusyBox v1.00-pre10 (2008.07.29-02:34+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
wlan[0,0]->



zrzut po podmianie na DD-WRT:

Cytat




řxInvalid PHY ID1 for enet0 port0. Expected 0x0243, read 0xffff
Ethernet eth0: MAC address 00:12:0e:b5:29:6c
IP: 192.168.1.254/255.255.255.0, Gateway: 192.168.1.254
Default server: 192.168.1.166

RedBoot(tm) bootstrap and debug environment [ROMRAM]
production release, version "2.1.3" - built 18:43:19, Sep 20 2007

Platform: ap61 (Atheros WiSOC)
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Copyright (C) 2007, NewMedia-NET GmbH.

Board: DLINK DIR-300
RAM: 0x80000000-0x81000000, [0x80040580-0x80fe1000] available
FLASH: 0xbfc00000 - 0xbfff0000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 4.000 seconds - enter ^C to abort
DD-WRT> fis load -l linux
Image loaded from 0x80041000-0x802d460c
DD-WRT> exec
Now booting linux kernel:
Base address 0x80030000 Entry 0x80041000
Cmdline :
ş§ŔD2ĹÜň°°° °°0ůŕá`áT°0Ĺú`ĂúĆŔ`ăĐ]
FIĹÜň°0° °°0ů
wgę=÷ńDrŔY{YÉ9pąŔŘđ°úi9öز#zs:20eÜ9ČĘjxŘű8]ËâŕdČĘč;(ňúň22ńp}ČĘč;(20ň22ąp}Čʨ
8:x2ypňńńYÓŔ\`słz`i=Üň(z˛0ćŔÔ2y`bg0°
eŔű¸hŤń3˙îŕŕĐ82*Č`Ô¨ČóîŕŕĐ82*Ę`Ô¨ČsęŘxr2*Č`Ô¨Čó9Řxr2*Ę`Ô¨ČóîŕŕĐ82*Č`Ô¨ČsęŘxr2*Ę`Ô¨ČóîŕŕĐ
 
obsy
Strzelam - inna prędkość ustawiona dla redboota (9600?) a inna standardowo na dd-wrt (115200). Zgadłem?
Masz niepotrzebny ruter, uszkodzony czy nie - ch?tnie przygarn? go.
http://eko.one.pl - prawie wszystko o OpenWrt
http://openrouter.info
 
iplab
Czy mógłbyś rozwinąć? Bo jeśli chodzi o ustawienie RedBoota to zggodnie ztym: http://www.shadowandy.net/2007/09/mini-flashing-guide-for-dir-300.htm ustawiłem na 115200. Może zapomniałem dodać, że router przy próbie ładowania linux.bin się restartuje a finalnie zawiesza.
 
obsy
To że się zawiesza to inna sprawa Smile

Zobacz ustaw po kolei różne prędkości. Będziesz miał sieczkę zamiast redbota, ale możesz zobaczyć output dd-wrt na czymś. Jak bym właśnie problem z prędkościami obstawiał, ale jak nie sprawdzisz to się nie dowiem czy mam rację.
Masz niepotrzebny ruter, uszkodzony czy nie - ch?tnie przygarn? go.
http://eko.one.pl - prawie wszystko o OpenWrt
http://openrouter.info
 
iplab
Sprawdziłem - przekonfigurowałem RedBoota na 115200 - także teraz widzę i RedBoota i start systemu. System natomiast się wywala i restartuje... ale za moment wgram jakąś świeższą wersję bo na dobrą sprawę to w tej chwili nawet nie wiem jaką mam....
 
iplab
OK, poniżej daję cały log. Jest problem z sieciówką i ma on pewnie związek z tym co na samym początku wypisuje redboot? Ten zapis pojawił się po wrzucenie redboota zrobionego pod DIR-300

Cytat


Invalid PHY ID1 for enet0 port0. Expected 0x0243, read 0xffff
Ethernet eth0: MAC address 00:12:0e:b5:29:6c
IP: 192.168.1.254/255.255.255.0, Gateway: 192.168.1.254
Default server: 192.168.1.166

RedBoot(tm) bootstrap and debug environment [ROMRAM]
production release, version "2.1.3" - built 18:43:19, Sep 20 2007

Platform: ap61 (Atheros WiSOC)
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Copyright (C) 2007, NewMedia-NET GmbH.

Board: DLINK DIR-300
RAM: 0x80000000-0x81000000, [0x80040580-0x80fe1000] available
FLASH: 0xbfc00000 - 0xbfff0000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 4.000 seconds - enter ^C to abort
DD-WRT> fis load -l linux
Image loaded from 0x80041000-0x802d45dc
DD-WRT> exec
Now booting linux kernel:
Base address 0x80030000 Entry 0x80041000
Cmdline :
Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.1.1) #22651 Sat Oct 10 02:36:51 CEST 2009
mips devid = 90
CPU revision is: 00019064
mem setup
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 64 (order: 6, 256 bytes)
Using 92.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 12948k/16384k available (2218k kernel code, 3436k reserved, 293k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
scanning for board data at A83FF000 (FFFFFFFF)
scanning for board data at A83FE000 (FFFFFFFF)
scanning for board data at A83FD000 (FFFFFFFF)
scanning for board data at A83FC000 (FFFFFFFF)
scanning for board data at A83FB000 (FFFFFFFF)
scanning for board data at A83FA000 (FFFFFFFF)
scanning for board data at A83F9000 (FFFFFFFF)
scanning for board data at A83F8000 (FFFFFFFF)
scanning for board data at A83F7000 (FFFFFFFF)
scanning for board data at A83F6000 (FFFFFFFF)
scanning for board data at A83F5000 (FFFFFFFF)
scanning for board data at A83F4000 (FFFFFFFF)
scanning for board data at A83F3000 (FFFFFFFF)
scanning for board data at A83F2000 (FFFFFFFF)
scanning for board data at A83F1000 (FFFFFFFF)
scanning for board data at A83F0000 (35333131)
found 1
Found board config at 0xa83f0000
Radio config found at offset 0xf8(0x1f8) (a83f00f8)
Generic PHY: Registered new driver
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
gpio_proc: module loaded and /proc/gpio/ created
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO3f8 MEM0 IRQ4): -28
serial8250 serial8250.0: unable to register port at index 1 (IO2f8 MEM0 IRQ3): -28
serial8250 serial8250.0: unable to register port at index 2 (IO3e8 MEM0 IRQ4): -28
serial8250 serial8250.0: unable to register port at index 3 (IO2e8 MEM0 IRQ3): -28
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
scanning for root partition

found squashfs at 100000
found RedBoot partition at [0xBFC00000]
found linux partition at [0xBFC30000]
Creating 8 MTD partitions on "spiflash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x003d0000 : "linux"
0x00100000-0x003d0000 : "rootfs"
0x003d0000-0x00400000 : "ddwrt"
0x003d0000-0x003e0000 : "nvram"
0x003e0000-0x003f0000 : "FIS directory"
0x003f0000-0x00400000 : "board_config"
0x00000000-0x00400000 : "fullflash"
watchdog hb: 60 ISR: 0x20 IMR: 0x8 WD : 0x9e230a61 WDC: 0x0
ar2315_wdt_init using heartbeat 60 s cycles 2400000000
watchdog hb: 60 ISR: 0x20 IMR: 0x88 WD : 0x8f07e624 WDC: 0x0
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 124k freed
starting Architecture code for fonera
Algorithmics/MIPS FPU Emulator v1.5
ar2315_wdt: starting watchdog w/timeout 60 seconds
watchdog hb: 60 ISR: 0x20 IMR: 0x89 WD : 0x8f0b13e4 WDC: 0x0
eth0: Atheros AR231x: 00:12:0e:b5:29:6c, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_busPffthy_addr=0:08)
ath_hal: module license 'Proprietary' taints kernel.
eth0: Configuring MAC for full duplex
nvram_commit(): end
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
sh: can't create /proc/sys/dev/wifi0/maxvaps: Permission denied
ath0
sh: can't create /proc/sys/dev/wifi0/csma: nonexistent directory
device ath0 entered promiscuous mode
br0: port 2(ath0) entering learning state
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
ifconfig: SIOCSIFADDR: No such device
No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
etherip: Ethernet over IPv4 tunneling driver
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable



Edytowany przez iplab dnia 27-01-2010 14:01
 
obsy
Nie ma drivera do obsługi ethernetu. W dlinku masz ipc175, tu widocznie masz coś innego. Uruchamia się, wiec poszukaj jeżeli przez serial masz dostęp do konsoli zrób lspci (jak nie ma to po /sys pogrzeb) i szukaj obrazu który to wspiera.
Masz niepotrzebny ruter, uszkodzony czy nie - ch?tnie przygarn? go.
http://eko.one.pl - prawie wszystko o OpenWrt
http://openrouter.info
 
iplab
Ten router nie ma switcha. Generalnie zaflashowałem linux.bin od GW-MF54G2 i działa. Potestuję to zaobaczę na ile skutecznie Wink

Dzięki za pomoc!
 
obsy
Aaa, na tym openwrt chodzi! A Ty dd-wrt... profanacja...
Edytowany przez obsy dnia 27-01-2010 16:41
Masz niepotrzebny ruter, uszkodzony czy nie - ch?tnie przygarn? go.
http://eko.one.pl - prawie wszystko o OpenWrt
http://openrouter.info
 
iplab
A tam profanacja... mam cztery sztuki to na każdej mogę coś innego zasadzić B)
 
Przejdź do forum
Zaloguj
Wprowadź adres e-mail lub nazwę użytkownika

Hasło



Nie masz jeszcze konta? Zarejestruj się.

Zapomniałeś/aś hasła?
Aktualnie online
· Gości online: 79

· Użytkowników online: 0

· Łącznie użytkowników: 24,115
· Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.

maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach

maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności",
więc prawdopodobnie gdzieś przepięcie.

servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.

maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?

servee
25-07-2024 09:22
W routerze RT-N18u siadły mi wszystkie porty LAN oraz WAN. Działa tylko radio. To jest naprawialne?

ptyku
29-06-2024 15:16
hi, mam problem z routerkiem RT-AC88u a dokładniej z wgraniem nowego firmware.

tamtosiamto
03-06-2024 16:24
poszlo w koncu -najpierw przez restoration jakies stare ddwrt, potem z menu update plik ac66u z art o zmianie 868l->ac66u

tamtosiamto
02-06-2024 21:44
trx size 44560384 > memory size 33554432 nigdy czegos takiego nie widzialem podczas flashowania rutera

tamtosiamto
02-06-2024 21:37
wgrywanie ddwrt z opisu zmiany softu z dlinka na asusa nic nie daje, dalej startuje tomato, wgranie ddwrt dla ac66u wchodzi, ale z niego tez nie da sie wgrac ofw asusa i merlina, kicha

tamtosiamto
02-06-2024 19:57
Probowal ktos wrocic z tomata do OFW ASAUSa na przerowbionym DIR868l -> rt-ac66u ? Ni cholery nie moge dac sobie rady.

86,056,219 unikalnych wizyt