mam nastepujacy problem. Wgralem OpenWrt na swojego Asusa WL500-W. Do tej pory pracowalem na tym routerze na orginalnym firmwarze gdzie mialem wpiety dysk twardy na USB i utworzona partycje za pomoca tego routera. Po wgraniu OpenWrt niemoge podmontowac dysku. Partycja niejest obslugiwana przez system. Po podlaczeniu dysku do komputera mam ten sam problem bo ani Mac ani Windows niesa wstanie odczytac danych z tej partycji. Jedyne co to pokazuja mi iz dysk ma utworzona partycje linuxa. Problem latwo mozna rozwiazac formatujac dysk, jednakze mam bardzo duzo cenny danych na nim i niewiem co teraz z tym fantem zrobic dalej ...
Masz na tym dysku ext2/ext3. Montuj normalnie przez mount -t ext2 (oczywiście wcześniej zainstalowałeś obsługę ext2/ext3, usb oraz ston kodowych - 437 conajmniej?)
Zrobilem wszystko wedlug tych dwoch tutoriali:
http://openwrt.livenet.pl/doku.php/hardware:usb
http://openwrt.livenet.pl/doku.php/hardware:usbhdd
Oczywiscie pomijajac kwestie formatowania dysku. Dogralem tak jak napisales obsluge stron kodowych 437.
Interfejs webowy rozpoznaje mi dysk i wypisuje cos takiego:
Bus Device Product Manufacturer VendorIDrodID USB version
04 3 USB2.0 Storage Device Cypress Semiconductor 04b4:6830
Wedlug tutriali powinien dysk sie automatycznie odmontowac jednakze jak wpisuje polecenie df to niewyswietla mi go. Jakie polecenie mam wydac dokladnie zeby podmontowac ten dysk ?
CPU revision is: 00029006
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Linux version 2.4.34 (nbd@ds10) (gcc version 3.4.6 (OpenWrt-2.0)) #3 Sun Sep 30 20:33:21 CEST 2007
Setting the PFC to its default value
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
CPU: BCM4704 rev 9 at 264 MHz
Using 132.000 MHz high precision timer.
Calibrating delay loop... 262.96 BogoMIPS
Memory: 30432k/32768k available (1462k kernel code, 2336k reserved, 100k data, 80k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 3) is a 16550A
b44.c:v0.93 (Mar, 2004)
PCI: Setting latency timer of device 00:01.0 to 64
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1e:8c9:e9:30
PCI: Setting latency timer of device 00:02.0 to 64
eth1: Broadcom 47xx 10/100BaseT Ethernet 00:90:4c:a1:00:2d
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x800000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x121cc8
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x000be400-0x001f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007f0000-0x00800000 : "nvram"
0x001f0000-0x007f0000 : "rootfs_data"
sflash: found no supported devices
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 360 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 80k freed
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'ASUS WL-500W'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Probing device eth0: found!
mini_fo: using base directory
mini_fo: using storage directoryjffs
jffs2.bbc: SIZE compression mode activated.
device eth0 entered promiscuous mode
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
br-lan: port 1(eth0) entering learning state
br-lan: port 1(eth0) entering forwarding state
br-lan: topology change detected, propagating
b44: eth1: Link is up at 100 Mbps, full duplex.
b44: eth1: Flow control is off for TX and off for RX.
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 01:02.0 to 64
PCI: Enabling device 01:02.0 (0004 -> 0006)
wl%d: 4.80.53.0 driver failed with code 12
unregister_netdevice: device wl%d/81077420 never was registered
Memory leak of bytes -2193
wl0: Broadcom BCM4329 802.11 Wireless Controller 4.80.53.0
device wl0 entered promiscuous mode
wl0: attempt to add interface with same source address.
br-lan: port 2(wl0) entering learning state
br-lan: port 2(wl0) entering forwarding state
br-lan: topology change detected, propagating
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with no debug enabled
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/
IPP2P v0.8.1_rc1 loading
imq driver loaded.
ipt_time loading
PCI: Setting latency timer of device 00:03.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Enabling device 01:03.0 (0000 -> 0001)
uhci.c: USB UHCI at I/O 0x100, IRQ 2
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 01:03.1 (0000 -> 0001)
uhci.c: USB UHCI at I/O 0x120, IRQ 2
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: $Revision: 1.275 $ time 08:58:50 Sep 29 2007
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Enabling device 01:03.2 (0000 -> 0002)
ehci_hcd 01:03.2: PCI device 1106:3104
ehci_hcd 01:03.2: irq 2, pci mem c035e000
usb.c: new USB bus registered, assigned bus number 4
EHCI: Enabling VIA 6212 workarounds
ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 4 ports detected
SCSI subsystem driver Revision: 1.00
hub.c: connect-debounce failed, port 2 disabled
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: new USB device 01:03.2-2, assigned address 2
br-lan: port 2(wl0) entering disabled state
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: ST350063 Model: 0A Rev: 0000
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0:<6>br-lan: port 2(wl0) entering disabled state
device wl0 left promiscuous mode
p1 < p5 >
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
device wl0 entered promiscuous mode
wl0: attempt to add interface with same source address.
br-lan: port 2(wl0) entering learning state
br-lan: port 2(wl0) entering forwarding state
br-lan: topology change detected, propagating
· Łącznie użytkowników: 24,115 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Maniek91PL
06-11-2024 22:37
dzięki !
maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia
Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa
overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.
maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.
overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?
maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach
maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności", więc prawdopodobnie gdzieś przepięcie.
servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.
maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
' target='_blank'>Link
rodID USB version
9:e9:30