Uzywam wlasnej kompilacji OpenWRT do odpalania Debiana z pendrive'a/dysku 2,5 zgodnie z mistrzowska koncepcja kolegi Tomka z http://wpkg.org/Running_Debian_on_ASU...00G_deluxe dla ktorego szacun.
Gdy odpalam system ze standardowymi u mnie 16MB-ami pamieci (sdram_init=0x000b) wszystko pieknie gra, zero problemow.
Jesli tylko uzyje pelnych 32MB (sdram_init=0x0009) to w trakcie odpalania sysytemu, od razu w trakcie pierwszych skryptow z rcS.d sypie mi sie kupa "segmentation fault'ow" i "bus error'ow".
Jednak zeby bylo smiezniej to nie zawsze tak jest. Mozna ogolnikowo powiedziec ze na jakies 10 odpalen routera, 3 z nich sa calkowicie poprawne, natomiast pozostale 7 konczy sie wspomnianymi bledami.
Czyli czasem slonce czasem deszcz.
Kompilowalem rozne jadra (revision 5375 , 6850, 9442, 10517) jednak bez rezultatu, ciagle to samo, ale tylko jak wlacze 32MB.
Na oryginalnym Kamikaze 7.09 z 32MB RAM'u tez czasem dostaje segmentation faulty, ale tylko na koncu procesu boot'owania i nie przeszkadza to w ogolnej pracy systemu.
Whiterussian rc6 and i oryginalny firmware Asus'a 1.9.7.5 dzialaja bez problemow, pewnie z racji jadra 2.4
Tak wiec nie bardzo wiem gdzie szukac problemu, czy w ustawieniach nvram czy w kernel'u.
Wielu osobom Debian smiga z 32MB na wl500gP bez zarzutow, ale z tego co zaobserwowalem to wszyscy maja wartosc "hardware_version" w nvram rowna "WL500gp-01-02-00-00"
U mnie natomiast pole to ma wartosc "WL500gH-01-00-00-00".Moze mam jakas starsza wersje tego routera? Czy ktos z was ma tez gH w nvramie i miewa/nie miewa podobne objawy?
Swoja droga nie bardzo tez rozumiem czemu nalezy uzyc wartosci 0x0009 aby uzyskac 32MB. Jesli by sie przyjrzec wartosciom ze strony Oleg'a, ktorego autorytet ciezko zakwestionowac (http://wl500g.dyndns.org/sdram.html) to wyglada jakby 0x0009 odnosilo sie do 64MB a nie 32MB, chyba ze ja cos nie kapcze (co jest bardzo prawdopodobne)
Myslalem ze mam moze cos nawalone ze zmienna "sdram_ncdl" , ale probowalem wielu opcji wlaczenie z sugerowana "zero" i tez NIC.
Bylbym wdzieczny za wszelakie sugestie, doswiadczenia zwlaszcza od osob majacych dziwne gH w polu hardware_version, bo powoli koncza mi sie pomysly a juz troche nad tym siedze. Znalazlem tylko jeden stary post z problemami podobnymi do moich, ale niestety nie moge zlapac autora (http://wl500g.info/showthread.php?t=6339)
Z gory dziekuje
Orlik
PS: Jesli ktos ma cierpliwosc to dolaczam logi z konsolki, jeden log z nieudanym, drugi z udanym bootowaniem tego samego softu
1. Nieudany boot z jaderka skompilowanego ze swiezego trunka r10517
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ¤T 12¤ë 14 15:54:18 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29006: 264MHz
Total memory: 33554432 KBytes
Total memory used by CFE: 0x80800000 - 0x8089B590 (636304)
Initialized Data: 0x80831700 - 0x80833DE0 (9952)
BSS Area: 0x80833DE0 - 0x80835590 (6064)
Local Heap: 0x80835590 - 0x80899590 (409600)
Stack Area: 0x80899590 - 0x8089B590 (8192)
Text (code) segment: 0x80800000 - 0x80831700 (202496)
Boot area (physical): 0x0089C000 - 0x008DC000
Relocation Factor: I:00000000 - D:00000000
Device eth0: hwaddr 00-17-31-DC-05-70, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3740 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.23.16 (orlik@testdeb) (gcc version 4.1.2) #2 Sat Feb 23 09:08:55 EST 2008
CPU revision is: 00029006
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists in Zone order. Total pages: 8128
Kernel command line: root=/dev/sda1 rootdelay=10 console=ttyS0,115200
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 132.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29628k/32768k available (2237k kernel code, 3140k reserved, 350k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
Registering a PCI bus after boot
PCI: Fixing up bridge 0000:00:00.0
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
JFFS2 version 2.2. (NAND) ÂA33; 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
b44.c:v1.01 (Jun 16, 2006)
eth0: Broadcom 10/100BaseT Ethernet 00:17:31:dc:05:70
eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x00120000-0x007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "Physically mapped flash"
0x007f0000-0x00800000 : "nvram"
PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:03.2
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd ssb0:2: SSB OHCI Controller
ohci_hcd ssb0:2: new USB bus registered, assigned bus number 2
ohci_hcd ssb0:2: irq 6, io mem 0x18003000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.0
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.1
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Waiting 10sec before mounting root device...
scsi 0:0:0:0: Direct-Access TOSHIBA MK1016GAP U1.1 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 124k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.86 booting
/etc/init.d/rc: line 77: 153 Bus error $@
/etc/init.d/rc: line 77: 169 Bus error $@
/etc/init.d/rc: line 77: 172 Bus error $@
/etc/rcS.d/S03udev: line 60: 207 Done grep '^[^#]' /etc/udev/links.conf
208 Bus error | while read type name arg1; do
[ "$type" -a "$name" -a ! -e "/dev/$name" -a ! -L "/dev/$name" ] || continue; case "$type" in
L)
ln -s $arg1 /dev/$name
;;
D)
mkdir -p /dev/$name
;;
M)
mknod -m 600 /dev/$name $arg1
;;
*)
log_warning_msg "links.conf: unparseable line ($type $name $arg1)"
;;
esac; if [ -x /sbin/restorecon ] then
/sbin/restorecon /dev/$name >/dev/null 2>/dev/null;
fi;
done
/etc/init.d/rc: line 77: 195 Bus error $@
/etc/init.d/rc: line 77: 227 Bus error $@
/etc/init.d/rc: line 77: 240 Bus error $@
/etc/rcS.d/S10checkroot.sh: line 24: 249 Bus error ( [ "$PASS" != 0 ] && [ "$PASS" != "" ] )
/etc/rcS.d/S10checkroot.sh: line 24: 250 Bus error ( [ "$FSTYPE" = "nfs" ] || [ "$FSTYPE" = "nfs4" ] )
Activating swap:.
/etc/rcS.d/S10checkroot.sh: line 24: 256 Bus error which on_ac_power >/dev/null 2>&1
EXT3 FS on sda1, internal journal
/etc/init.d/rc: line 77: 245 Bus error $@
Setting the system clock..
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
System Clock set. Local time: Sat Jan 1 00:00:19 UTC 2000.
/etc/init.d/rc: line 77: 267 Bus error $@
/lib/init/mount-functions.sh: line 23: 278 Bus error which selinuxenabled >/dev/null 2>&1
/etc/init.d/rc: line 77: 273 Bus error $@
Cleaning up ifupdown....
/etc/init.d/rc: line 77: 322 Bus error $@
/etc/init.d/rc: line 77: 330 Bus error $@
/etc/init.d/rc: line 77: 332 Bus error $@
Loading device-mapper support.
/etc/init.d/rc: line 77: 339 Bus error $@
/etc/rcS.d/S30checkfs.sh: line 62: 348 Bus error which on_ac_power >/dev/null 2>&1
Will now check all file systems.
fsck 1.40-WIP (14-Nov-2006)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
/etc/init.d/rc: line 77: 346 Bus error $@
/etc/rcS.d/S30procps.sh: line 22: 354 Bus error which sysctl >/dev/null
/etc/init.d/rc: line 77: 353 Bus error $@
Will now mount local filesystems:.
Will now activate swapfile swap:done.
/etc/init.d/rc: line 77: 361 Bus error $@
/etc/init.d/bootclean: line 169: 376 Bus error which find >/dev/null 2>&1
/etc/rcS.d/S36mountall-bootclean.sh: line 13: 374 Bus error /etc/init.d/bootclean
/etc/init.d/rc: line 77: 373 Bus error $@
/etc/init.d/rc: line 77: 377 Bus error $@
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Added VLAN with VID == 1 to IF -:eth0:-
WARNING: VLAN 1 does not work with many switches,
consider another number if you have problems.
/etc/init.d/rc: line 77: 386 Bus error $@
Setting up networking.../etc/init.d/rc: line 77: 399 Bus error $@
Configuring network interfaces...ifup: failed to open statefile /etc/network/run/ifstate: No such file or directory
failed.
/etc/init.d/rc: line 77: 406 Bus error $@
/etc/init.d/rc: line 77: 416 Bus error $@
/etc/init.d/bootclean: line 169: 424 Bus error which find >/dev/null 2>&1
/etc/rcS.d/S46mountnfs-bootclean.sh: line 13: 422 Bus error /etc/init.d/bootclean
/etc/init.d/rc: line 77: 421 Bus error $@
/etc/rcS.d/S55bootmisc.sh: line 16: 432 Bus error chgrp utmp /var/run/utmp
/etc/rcS.d/S55bootmisc.sh: line 16: 433 Segmentation fault uname -snrvm >/var/run/motd
/etc/rcS.d/S55bootmisc.sh: line 16: 435 Bus error which dmesg >/dev/null 2>&1
/etc/init.d/rc: line 77: 428 Bus error $@
/etc/init.d/rc: line 77: 437 Bus error $@
/etc/init.d/rc: line 77: 444 Bus error $@
/etc/init.d/rc: line 77: 448 Bus error $@
INIT: Entering runlevel: 2
Starting system log daemon: syslogd/etc/rc2.d/S10sysklogd: line 14: 458 Bus error chown root:adm /dev/xconsole
.
/etc/init.d/rc: line 77: 456 Bus error $@
Starting kernel log daemon: klogd.
/etc/init.d/rc: line 77: 464 Bus error $@
/etc/init.d/rc: line 77: 470 Bus error $@
/etc/init.d/rc: line 77: 477 Bus error $@
/etc/init.d/rc: line 77: 478 Bus error $@
* Not starting internet superserver: no services enabled.
/etc/init.d/rc: line 77: 480 Bus error $@
/etc/init.d/rc: line 77: 486 Bus error $@
/etc/rc2.d/S20ssh: line 7: 488 Bus error ( /usr/sbin/sshd -\? 2>&1 | grep -q OpenSSH ) 2>/dev/null
/etc/init.d/rc: line 77: 487 Bus error $@
Signal 10 (BUS) caught by ps (procps version 3.2.7).
Please send bug reports to or
Starting Asterisk PBX:
Signal 10 (BUS) caught by ps (procps version 3.2.7).
Please send bug reports to or
asterisk.
/etc/init.d/rc: line 77: 506 Bus error $@
Jan 1 01:00:38 WARNING[521]: manager.c:1743 init_manager: Unable to bind socket: Cannot assign requested address
Starting periodic command scheduler: crond.
/etc/init.d/rc: line 77: 528 Bus error $@
Running local boot scripts (/etc/rc.local)/etc/rc2.d/S99rc.local: line 17: 540 Bus error /etc/rc.local
failed!
/etc/init.d/rc: line 77: 538 Bus error $@
/etc/init.d/rc: line 77: 546 Bus error $@
/etc/rc2.d/S99stop-bootlogd: line 17: 549 Bus error /etc/init.d/bootlogd stop
/etc/init.d/rc: line 77: 548 Bus error $@
2. Udany boot z tego samego jaderka skompilowanego z trunka r10517
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ¤T 12¤ë 14 15:54:18 CST 2005 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.23.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29006: 264MHz
Total memory: 33554432 KBytes
Total memory used by CFE: 0x80800000 - 0x8089B590 (636304)
Initialized Data: 0x80831700 - 0x80833DE0 (9952)
BSS Area: 0x80833DE0 - 0x80835590 (6064)
Local Heap: 0x80835590 - 0x80899590 (409600)
Stack Area: 0x80899590 - 0x8089B590 (8192)
Text (code) segment: 0x80800000 - 0x80831700 (202496)
Boot area (physical): 0x0089C000 - 0x008DC000
Relocation Factor: I:00000000 - D:00000000
Device eth0: hwaddr 00-17-31-DC-05-70, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3740 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.23.16 (orlik@testdeb) (gcc version 4.1.2) #2 Sat Feb 23 09:08:55 EST 2008
CPU revision is: 00029006
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists in Zone order. Total pages: 8128
Kernel command line: root=/dev/sda1 rootdelay=10 console=ttyS0,115200
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 132.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29628k/32768k available (2237k kernel code, 3140k reserved, 350k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
Registering a PCI bus after boot
PCI: Fixing up bridge 0000:00:00.0
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
JFFS2 version 2.2. (NAND) ÂA33; 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
b44.c:v1.01 (Jun 16, 2006)
eth0: Broadcom 10/100BaseT Ethernet 00:17:31:dc:05:70
eth1: Broadcom 10/100BaseT Ethernet 40:10:18:00:00:2d
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x00120000-0x007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "Physically mapped flash"
0x007f0000-0x00800000 : "nvram"
PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:03.2
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd ssb0:2: SSB OHCI Controller
ohci_hcd ssb0:2: new USB bus registered, assigned bus number 2
ohci_hcd ssb0:2: irq 6, io mem 0x18003000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.0
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.1
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
Waiting 10sec before mounting root device...
scsi 0:0:0:0: Direct-Access TOSHIBA MK1016GAP U1.1 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 124k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap:.
Will now check root file system:fsck 1.40-WIP (14-Nov-2006)
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/sda1
/dev/sda1: clean, 15636/1177344 files, 198929/2351152 blocks
.
EXT3 FS on sda1, internal journal
Setting the system clock..
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
System Clock set. Local time: Sat Jan 1 00:00:24 UTC 2000.
Cleaning up ifupdown....
Loading kernel module ieee80211_crypt.
Loading kernel module ieee80211softmac.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
Loading kernel module ieee80211.
Loading kernel module bcm43xx.
FATAL: Module bcm43xx not found.
Loading device-mapper support.
Will now check all file systems.
fsck 1.40-WIP (14-Nov-2006)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables...done.
Will now mount local filesystems:.
Will now activate swapfile swap:done.
Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Added VLAN with VID == 1 to IF -:eth0:-
WARNING: VLAN 1 does not work with many switches,
consider another number if you have problems.
Setting up networking....
Configuring network interfaces...done.
Initializing random number generator...done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
* Not starting internet superserver: no services enabled.
Starting OpenBSD Secure Shell server: sshd.
Starting Asterisk PBX: asterisk.
Starting periodic command scheduler: crond.
Running local boot scripts (/etc/rc.local).
· Łącznie użytkowników: 24,115 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Maniek91PL
06-11-2024 22:37
dzięki !
maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia
Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa
overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.
maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.
overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?
maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach
maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności", więc prawdopodobnie gdzieś przepięcie.
servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.
maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
' target='_blank'>Link
