' target='_blank'>Link
26 Listopada 2024 00:12:45
Nawigacja
· Strona Główna
· Forum
· Tomato by Shibby
· FreshTomato

Wątki na forum
Najnowsze dyskusje
· DIR868l OFW asus vs ...
· Nowe routery: UX, UC...
· [S] Asus RT-AC56U
· Szukam zaproszenia n...
· [MOD] FreshTomato-AR...
· Asus RT-AC5300 ,prob...
· archer c6 v3.20
· [S] Nighthawk R7000P...
· [S]Asus RT-AC5300 - ...
· Tanie N100 na promce...
· net z telefonu wifi+...
· Tomato - bugi/proble...
· HUAWEI z światłowodem
· Asus TUF-AX3000_V2 p...
· rt-ax88upro częste ...
· [Howto] Xpenology na...
· Jaki router pod Open...
· Ruter z tomato
· Czy to jeszcze NAS?
· RT AC66U B1
Najpopularniejsze obecnie wątki
· DIR868l OFW asus ... [11]
· Nowe routery: UX,... [0]
· [S] Asus RT-AC56U [0]
Ankieta
Jaki procesor posiada twój router?

Broadcom MIPSEL
Broadcom MIPSEL
36% [151 głosów]

Broadcom ARM
Broadcom ARM
52% [219 głosów]

Atheros
Atheros
5% [22 głosów]

Marvell
Marvell
1% [4 głosów]

Ralink
Ralink
1% [3 głosów]

Intel/AMD/VIA
Intel/AMD/VIA
1% [5 głosów]

Żaden z powyższych
Żaden z powyższych
4% [15 głosów]

Ogółem głosów: 419
Musisz zalogować się, aby móc zagłosować.
Rozpoczęto: 02/02/2015 09:38
Twoje IP
18.226.248.88
Zobacz wątek
OpenLinksys » :: ROUTERY :: » Asus
 Drukuj wątek
RT-AC56U uceglony
proper
Top  #1 Drukuj post
Dodano 15-03-2017 19:47
Router Rt-AC56U nie wstaje, po włączeniu migną raz diody z tyłu i power świeci cały czas, więcej żadne Led. Komputer nie odnajduje IP routera, po ustawieniu na sztywno ping też nie idzie. Czyszczenie NVRAM nie pomaga, w recovery mode też nie wchodzi. Udało mi się połączyć przez serial, czyszczenie nvram nic nie daje ifconfig - error, próbowałem ustawić też nie da rady,
mac na et0 jest, na 0: nie pokazuje nic na 1: jest
po serialu wyrzuca to:
Decompressing...done

SHMOO VER 1.13

PKID07DC06011801080000000000001A103F01000000

S3004026B
00001C60


RDLYW0 00000004

RDENW0 00000048

RDQSW0

0000000000111111111122222222223333333333444444444455555555556666
0123456789012345678901234567890123456789012345678901234567890123
00 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++
01 -----------------+++++++++++++++++++++++X+++++++++++++++++++++++
02 ---------------++++++++++++++++++++++++X++++++++++++++++++++++++
03 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
04 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
05 --------------+++++++++++++++++++++++++X++++++++++++++++++++++++
06 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++
07 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++
08 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
09 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
10 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
11 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
12 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
13 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
14 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
15 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++


PW0

0000000000111111111122222222223333333333444444444455555555556666
0123456789012345678901234567890123456789012345678901234567890123
00 -------++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
01 ------------++++++++++++++++++++++++++X+++++++++++++++++++++++++
02 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
03 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
04 --+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++
05 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
06 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
07 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
08 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
09 ---++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++
10 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
11 -+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
12 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
13 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
14 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++
15 ++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++


NW0

0000000000111111111122222222223333333333444444444455555555556666
0123456789012345678901234567890123456789012345678901234567890123
00 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++
01 -----------------+++++++++++++++++++++++X+++++++++++++++++++++++
02 --------------+++++++++++++++++++++++++X++++++++++++++++++++++++
03 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
04 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++
05 --------------+++++++++++++++++++++++++X++++++++++++++++++++++++
06 --------------+++++++++++++++++++++++++X++++++++++++++++++++++++
07 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++++
08 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
09 ----------+++++++++++++++++++++++++++X++++++++++++++++++++++++++
10 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
11 --------++++++++++++++++++++++++++++X+++++++++++++++++++++++++++
12 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
13 ----++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++
14 ------+++++++++++++++++++++++++++++X++++++++++++++++++++++++++++
15 -----+++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++


WRDQW0

0000000000111111111122222222223333333333444444444455555555556666
0123456789012345678901234567890123456789012345678901234567890123
00 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
01 -+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++-
02 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
03 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
04 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
05 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
06 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
07 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
08 ++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++---
09 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
10 +++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++--
11 +++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++--
12 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
13 ++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++---
14 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-
15 +++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-


WRDMW0 00000031
WRDMW0 00000030


ADDR

0000000000111111111122222222223333333333444444444455555555556666
0123456789012345678901234567890123456789012345678901234567890123
00 ++++++++++++++++++++++++++++S++X++++++++++++++++++++++++++++++++

Decompressing...done
Detect CPU turbo button...

CFE version 6.30.163.2002 (r382208) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: ? 4? 18 09:25:12 CST 2013 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 533 MHz
Info: DDR frequency set from clkfreq=800,*533*
CPU type 0x0: 800MHz
Tot mem: 262144 KBytes

CFE mem: 0x00F00000 - 0x01192F4C (2699084)
Data: 0x00F4B644 - 0x00F4BA8C (1096)
BSS: 0x00F4BA98 - 0x00F90F4C (283828)
Heap: 0x00F90F4C - 0x01190F4C (2097152)
Stack: 0x01190F4C - 0x01192F4C (8192)
Text: 0x00F00000 - 0x00F42394 (271252)

Null Rescue Flag.
boot the image...
go load
Loader:raw Filesys:tftp Dev:(null) File:: Options:(null)
Loading: TFTP Server.
Failed.
Could not load :: Error
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: .. 1262094 bytes read
Entry at 0x00008000
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (Ope nWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 SMP Fri Sep 4 14:50:34 CEST 2015
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] Machine model: Asus RT-AC56U (BCM4708)
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c6dd4000 s5952 r8192 d22720 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 65280
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 255948K/262144K available (2886K kernel code, 106K rwdata , 404K rodata, 180K init, 276K bss, 6196K reserved, 131072K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc033edc4 (3292 kB)
[ 0.000000] .init : 0xc033f000 - 0xc036c000 ( 180 kB)
[ 0.000000] .data : 0xc036c000 - 0xc03869b8 ( 107 kB)
[ 0.000000] .bss : 0xc03869b8 - 0xc03cbacc ( 277 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C: platform modifies aux control register: 0x0a130000 -> 0x7a53 0001
[ 0.000000] L2C: platform provided aux values permit register corruption.
[ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x7 a530001
[ 0.000000] L2C-310 erratum 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310: enabling full line of zeros but not enabled in Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[ 0.000014] sched_clock: 64 bits at 400MHz, resolution 2ns, wraps every 27487 79069440ns
[ 0.008559] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
[ 0.101309] pid_max: default: 32768 minimum: 301
[ 0.106267] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.113132] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.120944] CPU: Testing write buffer coherency: ok
[ 0.126250] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.132255] Setting up static identity map for 0x11a60 - 0x11a94
[ 0.140264] CPU1: Booted secondary processor
[ 0.178362] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.178447] Brought up 2 CPUs
[ 0.191876] SMP: Total of 2 processors activated (3188.32 BogoMIPS).
[ 0.198466] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[ 0.207181] CPU: This may indicate a broken bootloader or firmware.
[ 0.220966] NET: Registered protocol family 16
[ 0.226336] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.260209] Switched to clocksource arm_global_timer
[ 0.266410] NET: Registered protocol family 2
[ 0.271843] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.279090] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.285685] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.292322] TCP: reno registered
[ 0.295725] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.301812] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.308542] NET: Registered protocol family 1
[ 0.313999] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.321203] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.327262] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.337578] msgmni has been set to 243
[ 0.342003] bounce: pool size: 64 pages
[ 0.346023] io scheduler noop registered
[ 0.350155] io scheduler deadline registered (default)
[ 0.355828] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.364724] console [ttyS0] disabled
[ 0.368550] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 117, base_baud = 6250000) is a 16550
[ 0.377742] console [ttyS0] enabled
[ 0.377742] console [ttyS0] enabled
[ 0.384874] bootconsole [earlycon0] disabled
[ 0.384874] bootconsole [earlycon0] disabled
[ 0.393927] 18000400.serial: ttyS1 at MMIO 0x18000400 (irq = 117, base_baud = 6250000) is a 16550
[ 0.404123] libphy: Fixed MDIO Bus: probed
[ 0.408276] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 0.413674] bcma: bus0: Found chip with id 53010, rev 0x00 and package 0x02
[ 0.420694] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
[ 0.429276] bcma: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, re v 0x01, class 0x0)
[ 0.438018] bcma: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, c lass 0x0)
[ 0.445975] bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x 04, class 0x0)
[ 0.454361] bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x 04, class 0x0)
[ 0.462743] bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x 04, class 0x0)
[ 0.471125] bcma: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x 04, class 0x0)
[ 0.479478] bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 0.488005] bcma: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 0.496581] bcma: bus0: Core 9 found: ARM Cortex A9 core (ihost) (manuf 0x4BF , id 0x510, rev 0x01, class 0x0)
[ 0.506516] bcma: bus0: Core 10 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x 01, class 0x0)
[ 0.514902] bcma: bus0: Core 11 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x 01, class 0x0)
[ 0.523300] bcma: bus0: Core 12 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01 , class 0x0)
[ 0.531525] bcma: bus0: Core 13 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x 506, rev 0x01, class 0x0)
[ 0.540874] bcma: bus0: Core 14 found: Denali DDR2/DDR3 memory controller (ma nuf 0x4BF, id 0x507, rev 0x01, class 0x0)
[ 0.551605] bcma: bus0: Core 15 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
[ 0.559646] bcma: bus0: Core 16 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
[ 0.569258] bcma: bus0: Core 17 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
[ 0.588429] bcm_nand bcma0:16: NAND Controller rev 6.01
[ 0.618429] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.624756] nand: AMD/Spansion NAND 128MiB 3,3V 8-bit
[ 0.629799] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 0.636936] mtd_read error while parsing (offset: 0x20000)!
[ 1.807986] random: nonblocking pool is initialized
[ 2.012104] 5 bcm47xxpart partitions found on MTD device bcm_nand
[ 2.018172] Creating 5 MTD partitions on "bcm_nand":
[ 2.023131] 0x000000000000-0x000000080000 : "boot"
[ 2.029689] 0x000000080000-0x000000200000 : "nvram"
[ 2.038133] 0x000000200000-0x000008000000 : "firmware"
[ 2.283649] 0x00000020001c-0x000000600000 : "linux"
[ 2.296859] 0x000000600000-0x000008000000 : "ubi"
[ 2.535256] bcm53xxspiflash spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[ 2.542582] bcm53xxspiflash: probe of spi32766.0 failed with error -2
[ 2.607493] can not parse nvram name (null)boardnum(null) with value ac:22:0b :1f:3a:78 got -22
[ 2.690932] bgmac bcma0:3: Found PHY addr: 30 (NOREGS)

uda się go jakoś ożywić czy to już koniec?
 
kille72
Top  #2 Drukuj post
Dodano 15-03-2017 19:58
https://openlinksys.info/forum/viewth...d_id=20952
 
proper
Top  #3 Drukuj post
Dodano 15-03-2017 21:21
jak wgrać CFE przez serial? bo LAN nie wstaje
 
kille72
Top  #4 Drukuj post
Dodano 15-03-2017 22:51
Czytałeś cały wątek?

Cytat

nvram get et0macaddr
nvram get 0:macaddr
nvram get 1:macaddr

pokazywały XX:XX:XX:XX:XX:XX

Ustawiłem
nvram set et0macaddr=40-16-7E-58-6C-90

potem commit i reboot i wstało
 
proper
Top  #5 Drukuj post
Dodano 16-03-2017 08:48
Czytalem caly

https://openlinksys.info/forum/viewth...d_id=20952 i
[url]https://openlinksys.info/forum/viewthread.php?thread_id=18046&rowstart=180
[/url]
jednak nie wstaje

nvram get et0macaddr jest MAC
nvram get 0:macaddr niema
nvram get 1:macaddr jest MAC

po
nvram set et0macaddr=mac mojego routera:78
nvram set 0:macaddr=mac mojego routera:7B
nvram set 1:macaddr=mac mojego routera:7C
nvram commit

zmienia sie zawartosc nvram lecz po restarcie wszystko wraca do wartosci takich jakie byly przed wpisaniem tych komend i router nie wstaje.

[ 0.178447] Brought up 2 CPUs
[ 0.191876] SMP: Total of 2 processors activated (3188.32 BogoMIPS).
[ 0.198466] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[ 0.207181] CPU: This may indicate a broken bootloader or firmware.

oznacza ze CFE jest uszkodzony?

[ 2.535256] bcm53xxspiflash spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[ 2.542582] bcm53xxspiflash: probe of spi32766.0 failed with error -2
[ 2.607493] can not parse nvram name (null)boardnum(null) with value ac:22:0b :1f:3a:78 got -22
[ 2.690932] bgmac bcma0:3: Found PHY addr: 30 (NOREGS)

nie moze odczytac bajtow ?
problem chyba z interfejsem wlan 0(2.4)

czy da sie wgrac inny CFE bez programatora i podniesionych interfejsow LAN?

Połączony z 16 marzec 2017 18:59:58:
zauważyłem że po

nvram set 0:macaddr=mac mojego routera:7B
nvram commit

w nvram dopisuje mac ale już po restarcie nvram bez tego wpisu

po nvram erase && commit
cały czas zostają pewne zmienne np: lista wcześniej podłączonych urządzeń z mac adresami, tak jakby nie czyściło nvram.

istnieje możliwość wgrania firmware w CFE?
albo jak przestawić go żeby przesłać firmware przez ftpt?

jak używać komend
flash - update a flash memory device
save - save a region of memory to a remote file via TFTP

żeby nie uwalić go całkiem

Połączony z 16 marzec 2017 20:27:23:
zrobiłem nowy bootloader (w oryginalnym zmieniłem adresy mac i secret_code)

czy mogę go wgrać komendą flash? jeśli tak to jak?

CFE> flash

flash [options] filename [flashdevice]

Copies data from a source file name or device to a flash memory device.
The source device can be a disk file (FAT filesystem), a remote file
(TFTP) or a flash device. The destination device may be a flash or eeprom.
If the destination device is your boot flash (usually flash0), the flash
command will restart the firmware after the flash update is complete

-noerase Don't erase flash before writing
-norescue Don't check anything
-offset=* Begin programming at this offset in the flash device
-size=* Size of source device when programming from flash to flash
-noheader Override header verification, flash binary without checking
-ndump dump nand flash
-block=* which block to dump
-forceflash Dangerous Command, Don't use if you don't know what you do
-erase Erase the partition, can set the offset and length
-cfe write to flash and stay at cfe command mode
-mem Use memory as source instead of a device
Edytowany przez proper dnia 16-03-2017 20:27
 
Przejdź do forum
Zaloguj
Wprowadź adres e-mail lub nazwę użytkownika

Hasło



Nie masz jeszcze konta? Zarejestruj się.

Zapomniałeś/aś hasła?
Aktualnie online
· Gości online: 72

· Użytkowników online: 0

· Łącznie użytkowników: 24,115
· Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.

Maniek91PL
06-11-2024 22:37
dzięki !Grin

maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia

Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa

overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.

maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.

overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?

maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach

maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności",
więc prawdopodobnie gdzieś przepięcie.

servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.

maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
95,801,213 unikalnych wizyt
Copyright © OpenLinksys 2006-2021


Powered by PHPFusion Copyright © 2024 PHP Fusion Inc
Released as free software without warranties under GNU Affero GPL v3.