Witam. Posiadam w/w router. Urządzenie nie komunikuje się poprzez kable Wan+Lan. Po podłączeniu przewodu sieciowego do komputera na routerze zapala sie odpowiednia kontrolka, komputer podaje komunikat o podłączeniu na szybkości 1Gbit jednak nie pobiera adresu sieciowego. Zachowuje się tak jakby switch nie był częścią routera. Przy uruchomieniu kontrolki się zapalają podczas ładowania routera ale cały czas jest brak komunikacji. Ta sama sytuacja jest ze złączem WAN. Co dziwne router działa bez problemu jako switch (połączenie na drodze internet-komputer poprzez 2 przewody jest przekazywane). W urządzeniu nie działa też sieć 2,4G. Jedyna droga jaką można się połączyć do urządzenia to Wifi 5G. Wgrane najnowsze oprogramowanie nie zmienia sytuacji. Jedyna możliwość wykorzystania urządzenia jest podłączenie modemu 3G/LTE to usb i skonfigurowanie połączenia w sekcji Dual-WAN jednak mi zależy na połączeniu internetu do gniazda WAN i odbiorze poprzez wifi i LAN. Router nie wykrywa połączenia wan chociaż kontrolka się swieci. W załączniku dołączę log z uruchomienia routera odczytany z wewnętrznego podłączenia serial w urzadzeniu gdyż log z samego routera jest niepełny. Nie ma tez możliwości wgrania softu poprzez system ratunkowy gdyż nie można wprowadzić routera w ten tryb - przycisk resetu jest sprawny gdyż po załadowaniu routera można nim zresetować do ustawień fabrycznych. Dziś pobawiłem sie jeszcze tym OpenWRT i udało mi się uruchomić internet w trybie Wifi2,4 client podłączony do starego routera przez Wifi a z sieci Wifi5G miałem internet na laptopie. Lan i Wan nie odpowiadają nadal. Co dziwne na oryginalnym Firmware Asusa sieć 2,4 wogule nie działa. ogladałem inne logi z tego routera i zaraz na poczatku bootloader wyswietla ze znalazł karte eth0 z podanym mac-adresem i ustawieniami sieci. Czy jest mozliwosc ze ktos podmienił loader na zły i jaka jest mozliwość nadpisania. Wgranie firmware stockowego pewnie nie wgrywa Bootloadera. Prosze o pomoc znawców tematu.
Połączony z 03 kwiecień 2016 22:53:24:
Decompressing...done
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Właśnie to mi wygląda na padnięty loader. Z podanej lokalizacji nie można pobrać plików gdyż są niedostępne. Jeśli można prosiłbym o te pliki i instrukcję jak to zrobić. Mam dostępny interfejs do połączenia routera przez RS-232. Następne pytanie skąd mam odczytać adresacje MAC wszystkich urządzeń. Pewnie lan,wan Wifi 2,4, wifi 5G mają różne. pozdrawiam
Połączony z 04 kwiecień 2016 11:33:56:
Zauważyłem jeszcze dziwną sprawę z adresacją MAC. Wan, LaN i Wlan0 maja identyczne adresy MAC - to z pewnością generuje błędy. Tylko Wlan1 ma inny adres i on nie sprawia problemów. Na sofcie od asusa nie działa też Wlan0 tylko DD-Wrt jakoś sobie z nim daje radę. Czy to może być błąd w CFE? Czy CFE inicjuje wszystkie urządzenia na starcie czy robi to dopiero linux który się ładuje z flash-a
Edytowany przez zombi6 dnia 04-04-2016 11:33
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0xce4
WARNING: at net/core/dev.c:3660 unregister_netdevice()
Call Trace:
[<8001206c>] dump_stack+0x8/0x34
[<801a8644>] unregister_netdev+0x1c/0x2c
[] et_init+0x220/0x6f4 [et]
wywala się sterownik switcha przez co nie wykrywa urządzeń et0 i et1 (lan & wan). Spróbuj wgrać tomato i zobacz czy coś się poprawi.
Proxmox VE:i5-13400T, 64GB RAM, 2x 512GB NVMe, 3x 2TB SSD, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology SA6400 VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
VPN jest mniejszy bo ma mniej dodatków (np. nie ma serwera http, php i mysql). Gdybyś miał router z sFlashem to mógłbyś dla testu wgrać najmniejszy by tylko zobaczyć czy zadziała.
Natomiast w AC66 jest już NAND flash wiec instalacja i tak pójdzie migiem. Wgraj zatem który chcesz.
Proxmox VE:i5-13400T, 64GB RAM, 2x 512GB NVMe, 3x 2TB SSD, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology SA6400 VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
Po zainstalowaniu Tomato w zakładce Device list jest tylko karta wifi eth1 przez którą się łączę do routera. Wan i lan oraz wifi 2.4 milczą dioda od 2,4 się nie swieci
wkleje log systemowy z tomato
Jan 1 01:00:08 unknown syslog.info syslogd started: BusyBox v1.23.2
Jan 1 01:00:08 unknown user.notice kernel: klogd started: BusyBox v1.23.2 (2016-03-16 09:35:02 CET)
Jan 1 01:00:08 unknown user.notice kernel: Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #2 Wed Mar 16 09:42:57 CET 2016
Jan 1 01:00:08 unknown user.warn kernel: CPU revision is: 00019749
Jan 1 01:00:08 unknown user.warn kernel: Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Jan 1 01:00:08 unknown user.warn kernel: Determined physical RAM map:
Jan 1 01:00:08 unknown user.warn kernel: memory: 07fff000 @ 00000000 (usable)
Jan 1 01:00:08 unknown user.warn kernel: memory: 08000000 @ 87fff000 (usable)
Jan 1 01:00:08 unknown user.debug kernel: Entering add_active_range(0, 0, 32767) 0 entries of 256 used
Jan 1 01:00:08 unknown user.debug kernel: Entering add_active_range(0, 557055, 589823) 1 entries of 256 used
Jan 1 01:00:08 unknown user.err syslog: module usbcore not found in modules.dep
Jan 1 01:00:08 unknown user.info kernel: Zone PFN ranges:
Jan 1 01:00:08 unknown user.warn kernel: Normal 0 -> 131072
Jan 1 01:00:08 unknown user.warn kernel: HighMem 131072 -> 589823
Jan 1 01:00:08 unknown user.info kernel: early_node_map[2] active PFN ranges
Jan 1 01:00:08 unknown user.warn kernel: 0: 0 -> 32767
Jan 1 01:00:08 unknown user.warn kernel: 0: 557055 -> 589823
Jan 1 01:00:08 unknown user.debug kernel: On node 0 totalpages: 65535
Jan 1 01:00:08 unknown user.debug kernel: Normal zone: 0 pages used for memmap
Jan 1 01:00:08 unknown user.debug kernel: Normal zone: 0 pages reserved
Jan 1 01:00:08 unknown user.debug kernel: Normal zone: 32767 pages, LIFO batch:7
Jan 1 01:00:08 unknown user.debug kernel: HighMem zone: 0 pages used for memmap
Jan 1 01:00:08 unknown user.debug kernel: HighMem zone: 32768 pages, LIFO batch:7
Jan 1 01:00:08 unknown user.warn kernel: Built 1 zonelists. Total pages: 65535
Jan 1 01:00:08 unknown user.notice kernel: Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Jan 1 01:00:08 unknown user.warn kernel: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Jan 1 01:00:08 unknown user.warn kernel: Primary data cache 32kB, 4-way, linesize 32 bytes.
Jan 1 01:00:08 unknown user.info kernel: Synthesized TLB refill handler (20 instructions).
Jan 1 01:00:08 unknown user.info kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan 1 01:00:08 unknown user.info kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan 1 01:00:08 unknown user.info kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan 1 01:00:08 unknown user.warn kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Jan 1 01:00:08 unknown user.warn kernel: CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Jan 1 01:00:08 unknown user.warn kernel: Using 300.000 MHz high precision timer.
Jan 1 01:00:08 unknown user.info kernel: console [ttyS0] enabled
Jan 1 01:00:08 unknown user.warn kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 01:00:08 unknown user.warn kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 01:00:08 unknown user.info kernel: Memory: 254760k/131068k available (2705k kernel code, 7084k reserved, 410k data, 208k init, 131072k highmem)
Jan 1 01:00:08 unknown user.debug kernel: Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
Jan 1 01:00:08 unknown user.warn kernel: Mount-cache hash table entries: 512
Jan 1 01:00:08 unknown user.info kernel: NET: Registered protocol family 16
Jan 1 01:00:08 unknown user.info kernel: usbcore: registered new interface driver usbfs
Jan 1 01:00:08 unknown user.info kernel: usbcore: registered new interface driver hub
Jan 1 01:00:08 unknown user.info kernel: usbcore: registered new device driver usb
Jan 1 01:00:08 unknown user.warn kernel: PCI: Initializing host
Jan 1 01:00:08 unknown user.warn kernel: PCI: Reset RC
Jan 1 01:00:08 unknown user.warn kernel: PCI: Initializing host
Jan 1 01:00:08 unknown user.warn kernel: PCI: Reset RC
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bus 0
Jan 1 01:00:08 unknown user.warn kernel: PCI/PCIe coreunit 0 is set to bus 1.
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:08 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:00.0 to 64
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:08 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:00.1 to 64
Jan 1 01:00:08 unknown user.warn kernel: PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bus 1
Jan 1 01:00:08 unknown user.warn kernel: PCI/PCIe coreunit 1 is set to bus 2.
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:08 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:00.0 to 64
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bridge
Jan 1 01:00:08 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:00.1 to 64
Jan 1 01:00:08 unknown user.warn kernel: PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
Jan 1 01:00:08 unknown user.warn kernel: PCI: Fixing up bus 2
Jan 1 01:00:08 unknown user.info kernel: NET: Registered protocol family 2
Jan 1 01:00:08 unknown user.info kernel: Time: MIPS clocksource has been installed.
Jan 1 01:00:08 unknown user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:08 unknown user.warn kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan 1 01:00:09 unknown user.warn kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 01:00:09 unknown user.info kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan 1 01:00:09 unknown user.info kernel: TCP reno registered
Jan 1 01:00:09 unknown user.warn kernel: highmem bounce pool size: 64 pages
Jan 1 01:00:09 unknown user.info kernel: squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
Jan 1 01:00:09 unknown user.info kernel: io scheduler noop registered (default)
Jan 1 01:00:09 unknown user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
Jan 1 01:00:09 unknown user.info kernel: N_HDLC line discipline registered.
Jan 1 01:00:09 unknown user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan 1 01:00:09 unknown user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
Jan 1 01:00:09 unknown user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
Jan 1 01:00:09 unknown user.info kernel: PPP generic driver version 2.4.2
Jan 1 01:00:09 unknown user.info kernel: MPPE/MPPC encryption/compression module registered
Jan 1 01:00:09 unknown user.info kernel: NET: Registered protocol family 24
Jan 1 01:00:09 unknown user.info kernel: PPPoL2TP kernel driver, V0.18.3
Jan 1 01:00:09 unknown user.info kernel: PPTP driver version 0.8.5
Jan 1 01:00:09 unknown user.err kernel: pflash: found no supported devices
Jan 1 01:00:09 unknown user.warn kernel: Boot partition size = 262144(0x40000)
Jan 1 01:00:09 unknown user.notice kernel: Creating 2 MTD partitions on "sflash":
Jan 1 01:00:09 unknown user.notice kernel: 0x00000000-0x00040000 : "pmon"
Jan 1 01:00:09 unknown user.notice kernel: 0x001f0000-0x00200000 : "nvram"
Jan 1 01:00:09 unknown user.warn kernel: Found a Zentel NAND flash with 2048B pages or 128KB blocks; total size 128MB
Jan 1 01:00:09 unknown user.warn kernel: lookup_nflash_rootfs_offset: offset = 0x0
Jan 1 01:00:09 unknown user.notice kernel: nflash: squash filesystem with lzma found at block 9
Jan 1 01:00:09 unknown user.notice kernel: Creating 2 MTD partitions on "nflash":
Jan 1 01:00:09 unknown user.notice kernel: 0x00000000-0x02000000 : "linux"
Jan 1 01:00:09 unknown user.notice kernel: 0x00133bdc-0x02000000 : "rootfs"
Jan 1 01:00:09 unknown user.info kernel: NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Zentel NAND 128MiB 3,3V 8-bit)
Jan 1 01:00:09 unknown user.debug kernel: Bad block table found at page 65408, version 0x01
Jan 1 01:00:09 unknown user.debug kernel: Bad block table found at page 65344, version 0x01
Jan 1 01:00:09 unknown user.debug kernel: nand_read_bbt: Bad block at 0x07fe0000
Jan 1 01:00:09 unknown user.notice kernel: Creating 3 MTD partitions on "brcmnand":
Jan 1 01:00:09 unknown user.notice kernel: 0x00000000-0x02000000 : "trx"
Jan 1 01:00:09 unknown user.notice kernel: 0x02000000-0x04000000 : "jffs2"
Jan 1 01:00:09 unknown user.notice kernel: 0x04000000-0x07f00000 : "brcmnand"
Jan 1 01:00:09 unknown user.warn kernel: dev_nvram_init: _nvram_init
Jan 1 01:00:09 unknown user.warn kernel: _nvram_init: allocat size= 65536
Jan 1 01:00:09 unknown user.info kernel: usbcore: registered new interface driver hiddev
Jan 1 01:00:09 unknown user.info kernel: usbcore: registered new interface driver usbhid
Jan 1 01:00:09 unknown user.info kernel: drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Jan 1 01:00:09 unknown user.debug hotplug[421]: Attached USB device 1-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/2/206]
Jan 1 01:00:09 unknown user.warn kernel: u32 classifier
Jan 1 01:00:09 unknown user.warn kernel: OLD policer on
Jan 1 01:00:09 unknown user.warn kernel: Netfilter messages via NETLINK v0.30.
Jan 1 01:00:09 unknown user.warn kernel: nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
Jan 1 01:00:09 unknown user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:09 unknown user.info kernel: ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
Jan 1 01:00:09 unknown user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Mar 16 2016 09:29:06]
Jan 1 01:00:09 unknown user.info kernel: NET: Registered protocol family 1
Jan 1 01:00:09 unknown user.info kernel: NET: Registered protocol family 10
Jan 1 01:00:09 unknown user.warn kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:09 unknown user.info kernel: NET: Registered protocol family 17
Jan 1 01:00:09 unknown user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear
Jan 1 01:00:09 unknown user.info kernel: All bugs added by David S. Miller
Jan 1 01:00:09 unknown user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 01:00:09 unknown user.info kernel: Freeing unused kernel memory: 208k freed
Jan 1 01:00:09 unknown user.warn kernel: Warning: unable to open an initial console.
Jan 1 01:00:09 unknown user.warn kernel: Failed to execute /sbin/preinit. Attempting defaults...
Jan 1 01:00:09 unknown user.warn kernel: emf: module license 'Proprietary' taints kernel.
Jan 1 01:00:09 unknown user.warn kernel: et_module_init: passivemode set to 0x0
Jan 1 01:00:09 unknown user.warn kernel: et_module_init: et_txq_thresh set to 0x0
Jan 1 01:00:09 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 01:00:09 unknown user.debug kernel: unregister_netdevice: device eth%d/87e15c00 never was registered
Jan 1 01:00:09 unknown user.warn kernel: WARNING: at net/core/dev.c:3659 unregister_netdevice()
Jan 1 01:00:09 unknown user.warn kernel: Call Trace:[<8002b35c>][<800117a4>][<800117a4>][<801ba164>][][][][][<800c92d4>][<800c93d4>][<800c94d4>][<800f3060>][<800f3060>][<800cac64>][<800cac44>][<8011f8c0>][<801048f4>][<80123a7c>][<8012400c>][<80123e08>][<801227b8>][<80123e08>][<80122920>][<80122de8>][<8002b458>][<80104728>][<8004e03c>][<80013524>]
Jan 1 01:00:09 unknown user.warn kernel: PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
Jan 1 01:00:09 unknown user.debug kernel: PCI: Setting latency timer of device 0000:01:01.0 to 64
Jan 1 01:00:09 unknown user.warn kernel: eth0: Broadcom BCM4331 802.11 Wireless Controller 6.30.102.9 (r366174)
Jan 1 01:00:09 unknown user.warn kernel: PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
Jan 1 01:00:09 unknown user.debug kernel: PCI: Setting latency timer of device 0000:02:01.0 to 64
Jan 1 01:00:09 unknown user.warn kernel: eth1: Broadcom BCM4360 802.11 Wireless Controller 6.30.102.9 (r366174)
Jan 1 01:00:09 unknown user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 01:00:09 unknown user.notice kernel: SCSI subsystem initialized
Jan 1 01:00:09 unknown user.info kernel: Initializing USB Mass Storage driver...
Jan 1 01:00:09 unknown user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 01:00:09 unknown user.info kernel: USB Mass Storage support registered.
Jan 1 01:00:09 unknown user.notice kernel: ufsd: driver (8.6 U86_r187446_b122, LBD=ON, acl, ioctl, rwm, ws, sd) loaded at c019c000
Jan 1 01:00:09 unknown user.warn kernel: NTFS (with native replay) support included
Jan 1 01:00:09 unknown user.warn kernel: optimized: speed
Jan 1 01:00:09 unknown user.warn kernel: Build_for__asus_n66u_2011-10-27_U86_r187446_b122
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 01:00:09 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:04.1 to 64
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd 0000:00:04.1: irq 6, io mem 0x18004000
Jan 1 01:00:09 unknown user.info kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
Jan 1 01:00:09 unknown user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 01:00:09 unknown user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 01:00:09 unknown user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 01:00:09 unknown user.info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2
Jan 1 01:00:09 unknown user.debug kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:09 unknown user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:00:09 unknown user.info kernel: vlan1: dev_set_allmulti(master, 1)
Jan 1 01:00:09 unknown user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Jan 1 01:00:09 unknown user.info kernel: hub 1-1:1.0: USB hub found
Jan 1 01:00:09 unknown user.info kernel: hub 1-1:1.0: 4 ports detected
Jan 1 01:00:09 unknown user.info kernel: vlan1: dev_set_promiscuity(master, 1)
Jan 1 01:00:09 unknown user.info kernel: device eth0 entered promiscuous mode
Jan 1 01:00:09 unknown user.info kernel: device vlan1 entered promiscuous mode
Jan 1 01:00:09 unknown user.warn kernel: wlc_phy_cal_init_acphy: NOT Implemented
Jan 1 01:00:09 unknown user.debug hotplug[473]: Attached USB device 1-1:1.0 [INTERFACE=9/0/0 PRODUCT=58f/6254/100]
Jan 1 01:00:10 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 01:00:10 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:10 unknown user.info kernel: br0: port 1(vlan1) entering forwarding state
Jan 1 01:00:10 unknown user.info init[1]: MultiWAN: MWAN is 1.
Jan 1 01:00:10 unknown user.warn kernel: vlan2: Setting MAC address to 10 c3 7b 42 69 f0.
Jan 1 01:00:10 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 01:00:10 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 01:00:10 unknown user.notice kernel: Ebtables v2.0 registered
Jan 1 01:00:10 unknown user.info kernel: device eth1 left promiscuous mode
Jan 1 01:00:10 unknown user.info kernel: br0: port 2(eth1) entering disabled state
Jan 1 01:00:10 unknown user.info kernel: vlan1: dev_set_allmulti(master, -1)
Jan 1 01:00:10 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 01:00:10 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 01:00:10 unknown user.info kernel: IMQ starting with 2 devices...
Jan 1 01:00:10 unknown user.info kernel: IMQ driver loaded successfully.
Jan 1 01:00:10 unknown user.info kernel: Hooking IMQ after NAT on PREROUTING.
Jan 1 01:00:10 unknown user.info kernel: Hooking IMQ before NAT on POSTROUTING.
Jan 1 01:00:11 unknown authpriv.warn dropbear[582]: Failed loading /etc/dropbear/dropbear_ecdsa_host_key
Jan 1 01:00:11 unknown authpriv.info dropbear[585]: Running in background
Jan 1 01:00:11 unknown daemon.info dnsmasq[594]: started, version 2.73 cachesize 4096
Jan 1 01:00:11 unknown daemon.info dnsmasq[594]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset Tomato-helper auth DNSSEC loop-detect no-inotify
Jan 1 01:00:11 unknown daemon.info dnsmasq[594]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 01:00:11 unknown daemon.info dnsmasq-dhcp[594]: DHCP, IP range 192.168.1.2 -- 192.168.1.51, lease time 1d
Jan 1 01:00:11 unknown daemon.warn dnsmasq[594]: failed to access /etc/resolv.dnsmasq: No such file or directory
Jan 1 01:00:11 unknown daemon.info dnsmasq[594]: read /etc/hosts - 2 addresses
Jan 1 01:00:12 unknown daemon.info dnsmasq[594]: read /etc/dnsmasq/hosts/hosts - 5 addresses
Jan 1 01:00:12 unknown daemon.info dnsmasq-dhcp[594]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 01:00:12 unknown user.info init[1]: NGinX - daemon not enabled cancelled generation of config file
Jan 1 01:00:12 unknown user.debug init[1]: starting rstats.
Jan 1 01:00:12 unknown user.debug init[1]: starting cstats.
Jan 1 01:00:13 unknown user.notice root: Stoping NFS Server ...
Jan 1 01:00:13 unknown user.notice root: NFS Server stoped ...
Jan 1 01:00:13 unknown user.notice root: MySQL successfully stoped
Jan 1 01:00:13 unknown user.notice root: Transmission daemon successfully stoped
Jan 1 01:00:13 unknown user.info init[1]: Asus RT-AC66U: Tomato 1.28.0000 MIPSR2-135 K26AC USB AIO-64K
Jan 1 01:00:17 unknown daemon.info dnsmasq-dhcp[594]: DHCPREQUEST(br0) 192.168.1.32 08:11:96:24:ab:fc
Jan 1 01:00:17 unknown daemon.info dnsmasq-dhcp[594]: DHCPACK(br0) 192.168.1.32 08:11:96:24:ab:fc DELL-Komputer
Jan 1 01:00:19 unknown daemon.err apcupsd[427]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see .
Jan 1 01:00:19 unknown daemon.err apcupsd[427]: apcupsd error shutdown completed
Jan 1 01:06:10 unknown daemon.info dnsmasq-dhcp[594]: DHCPREQUEST(br0) 192.168.1.32 08:11:96:24:ab:fc
Jan 1 01:06:10 unknown daemon.info dnsmasq-dhcp[594]: DHCPACK(br0) 192.168.1.32 08:11:96:24:ab:fc DELL-Komputer
Jan 1 01:00:09 unknown user.warn kernel: et_module_init: passivemode set to 0x0
Jan 1 01:00:09 unknown user.warn kernel: et_module_init: et_txq_thresh set to 0x0
Jan 1 01:00:09 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 01:00:09 unknown user.debug kernel: unregister_netdevice: device eth%d/87e15c00 never was registered
Jan 1 01:00:09 unknown user.warn kernel: WARNING: at net/core/dev.c:3659 unregister_netdevice()
Jan 1 01:00:09 unknown user.warn kernel: Call Trace:[<8002b35c>][<800117a4>][<800117a4>][<801ba164>][][][][][<800c92d4>][<800c93d4>][<800c94d4>][<800f3060>][<800f3060>][<800cac64>][<800cac44>][<8011f8c0>][<801048f4>][<80123a7c>][<8012400c>][<80123e08>][<801227b8>][<80123e08>][<80122920>][<80122de8>][<8002b458>][<80104728>][<8004e03c>][<80013524>]
nadal to samo. Nadal nie jest wykrywany switch.
Proxmox VE:i5-13400T, 64GB RAM, 2x 512GB NVMe, 3x 2TB SSD, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology SA6400 VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
Teraz pytanie jak to naprawić. Switch jak i port wan fizycznie nie są popalone. Reagują na podłączenie przewodu. Do tego komputer podaje prędkości 1Gbit zarówno na 4 lanach jak i porcie Wan. Co może być powodem że switch nie łączy się z oprogramowaniem routera. Podczas ładowania systemu kontrolki kilkukrotnie się zapalają co świadczy że router steruje switchem jednak nie ma łączności z nim. Do tego problem z siecią Wifi2.4 Na Tomato i Oryginalnym sofcie asusa nie działa a na DD-WRT funkcjonuje w trybie klienta.
Połączony z 04 kwiecień 2016 14:17:29:
Router jest dość drogi i szkoda mi go wyrzucać. Gdyby to był sprzęt za 100zł nie zastanawiałbym się ani chwili.
Połączony z 04 kwiecień 2016 14:20:28:
Być może problem jest w loaderze CFE. Jeśli jest jakaś opcja wymiany (upgrade) CFE to prosiłbym o instrukcję. Podobno trzeba tam wyedytować adresy Mac urządzeń ale nikt nie ma opisu jak postepować
Połączony z 04 kwiecień 2016 14:24:27:
znalazłem w sieci log z ładowania identycznego routera. Widać tam że po init dev następuje wykrycie karty sieciowej a później jej konfiguracja pod tryb ratunkowy. W moim wrzuconym na początku logu tego nie ma.
▒Decompressing...done!!
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.29 (r338244)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 08-60-6E-BD-FD-A8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
Edytowany przez zombi6 dnia 04-04-2016 14:24
Mam jeszcze pytanie. Jeśli na tabliczce w/w routera mam adres mac: 10:C3:7B:42:69:E0 to jakie adresy będą miały interfejsy sieciowe. Jestem na etapie tworzenia nowego CFE i nie chcę czegoś źle wpisać bo może mieć to wpływ na dalsze działanie routera i na dostęp do niego po upgrade. Jedyny działający u mnie interfejs Eth1 (wifi5G) ma adres: 10:C3:7B:42:69:E2
przy czym poczatek poza koncowka jest wszedzie taki sam.
Połączony z 04 kwiecień 2016 17:27:55:
sprawdzilem na tabliczce routerka mam MAC koncowka : D0 a reszta tak samo
Edytowany przez Adooni dnia 04-04-2016 17:27
Orange 300/50 Mb/s + ONT Terminal HPE MS gen8 Proxmox 7.0-11 VMs: Router OPNsense 23.X-amd64 and OMV HPE MicroServer gen8: Xeon E3-1265Lv2, 16GB (2x KTH-PL316E/8G), HP 331T, 4x4TB WD RED Asus RT-AC68U AccessPoint
Witam. CFE podmienionie jednak nie zmieniło nic w działaniu routera. być może mam źle wprowadzone adresy mac urządzeń. Zamieszczę log z programu CFEEdit po wczytaniu pliku pobranego z routera. Być może ktoś porówna ze swoim podobnym modelem asusa na pewno zależności końcówek Mac-adresów są identyczne w modelu który posiada Wifi 2,4 i 5G
Połączony z 05 kwiecień 2016 17:48:40:
adres z loga: et0macaddr=10:C3:7B:42:69:E0 pokrywa się z adresem na tabliczce routera. Nie mam pewności czy kolejne 2 z tamtego loga są poprawnie wpisane
Połączony z 09 kwiecień 2016 17:46:20:
dziękuję za chęci pomocy. Router sprzedany na portalu aukcyjnym jako uszkodzony. pozdrawiam
Edytowany przez zombi6 dnia 09-04-2016 17:46
Witam,
odgrzebię trochę temat ,nabyłem od kolegi niniejszy routerek i przy urzyciu wstecznej inżynierii postawiłem go na nogi,ale żeby nie było zbyt pięknie jest lekki problem z pomidorem.Po wrzuceniu tomato potrzebne jest czyszczenie nvram aby zaskoczyło 5gz niestety po tej operacji router wraca do punktu wyjścia opisany przez kolegę na początku tematu ,nie wykrywa swicha działa tylko wl_5gz, z kolei przy ddwrt nie napotkałem jeszcze na ten problem .Wolałbym wrócić do tomato wiec mam nadzieję że ktoś pomoże .W rzucam log z ładowania dd-wrt może ktoś bardziej ogarnięty będzie wiedział o co chodzi.
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
[1 init:init_main +25] recv signal 14 from pid [1:/sbin/init] (from user)
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
[1 init:init_main +68] recv signal 14 from pid [1:/sbin/init] (from user)
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
udhcpc_wan:: leasefail
PLudhcpc_wan:: leasefail [i:httpd] 271:notify_rc start_autodet[1 init:init_main +233] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=start_autodet
[1 init:handle_notifications +233] running: 2 autodet
handle_notifications() end
[1 init:init_main +233] recv signal 14 from pid [1:/sbin/init] (from user)
update_variables: [apply] [start_webs_update] [3]
value x_Setting=1
set x_Setting=1
271: check_action 0
271: set_action 7
271: set_action 0 [i:httpd] 271:notify_rc start_webs_update[1 init:init_main +242] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=start_webs_update
[1 init:handle_notifications +242] running: 2 webs_update
handle_notifications() end
[1 init:init_main +242] recv signal 14 from pid [1:/sbin/init] (from user)
update_variables: [apply] [saveNvram] [0]
value sw_mode=1
value wl1_ssid=ASUS_5G
validate_instance(0x07a2): nvram set wl0_crypto = aes
validate_instance(0x07a2): nvram set wl1_crypto = aes
value time_zone=UTC-1DST_2
set time_zone=UTC-1DST_2
value w_Setting=1
set w_Setting=1
271: check_action 0
271: set_action 7
<****>freeze the duck, 13s left!
306: check_action 7
271: set_action 0
306: check_action 0
306: set_action 7
update_variables: [apply] [restart_time;restart_wireless] [5]
value force_change=1
set force_change=1
value x_Setting=1
271: check_action 7
<****>freeze the duck, 8s left!
271: check_action 7
271: check_action 7
306: set_action 0
271: check_action 0
271: set_action 7
271: set_action 0 [i:httpd] 271:notify_rc restart_time;restart_wireless
<****>freeze the duck, 15s left!
[1 init:init_main +255] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=restart_time
[1 init:handle_notifications +255] running: 3 time
start_logger:
starting ntp...
writting prerouting eth0 0.0.0.0 eth0 0.0.0.0 br0 192.168.1.1
wanport_status(0) 0
[1 init:filter_setting +255] write porttrigger
[1 init:filter_setting +255] write wl filter
[1 init:filter_setting +255] write url filter
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
goto again(1)...
cmd[0]=restart_wireless
[1 init:handle_notifications +256] running: 3 wireless
killall_tk: waiting name=networkmap n=9
killall_tk: waiting name=wps_monitor n=9
killall_tk: waiting name=wps_monitor n=8
killall_tk: waiting name=wps_monitor n=7
killall_tk: waiting name=wps_monitor n=6
killall_tk: waiting name=wps_monitor n=5
killall_tk: waiting name=eapd n=9
vlan1: cmd=14: Operation not supported
_ifconfig: name=eth1 flags=0000 addr=(null) netmask=(null)
eth2: cmd=14: No such device
catch_sig(0x05aa): [watchdog] Handle WPS LED for WPS Stop
hotplug net INTERFACE=eth1 ACTION=remove
hotplug net INTERFACE=vlan1 ACTION=remove
hotplug net INTERFACE=vlan2 ACTION=remove
hotplug net INTERFACE=eth0 ACTION=remove
hotplug_net(): sent event 1
hotplug_net(): sent event 1
hotplug_net(): sent event 1
[1 init:init_nvram +257] init_nvram for model(39)
num_of_mssid_support(0x0098): [mssid] support [3] mssid
hotplug_net(): sent event 1
set_wltxpower(0x023b): unit: 0, txpower: 100
set_wltxpower(0x023b): unit: 1, txpower: 100
1: check_action 0
1: set_action 7
calc: WIRED not found setting sync=1
calc: WIRELESS0 not found setting sync=1
1: set_action 0
wl_module_init: passivemode set to 0x0
eth0: Broadcom BCM4331 802.11 Wireless Controller 6.30.163.2002 (r382208)
eth1: Broadcom BCM4360 802.11 Wireless Controller 6.30.163.2002 (r382208)
<****>freeze the duck, 10s left!
generate_wl_para(0x0a54): unit 0 subunit -1
num_of_mssid_support(0x0098): [mssid] support [3] mssid
generate_wl_para(0x0d54): bw: 0
generate_wl_para(0x0d56): chanspec: 0
generate_wl_para(0x0d57): bw_cap: 3
generate_wl_para(0x0d5d): obss_coex: 1
wlconf_pre(0x17a2): set vhtmode 0
generate_wl_para(0x0a54): unit 1 subunit -1
num_of_mssid_support(0x0098): [mssid] support [3] mssid
generate_wl_para(0x0d54): bw: 0
generate_wl_para(0x0d56): chanspec: 0
generate_wl_para(0x0d57): bw_cap: 7
generate_wl_para(0x0d5d): obss_coex: 0
wlconf_wlc_phy_cal_init_acphy: NOT Implemented
pre(0x179d): set vhtmode 1
vlan1: cmd=14: No such device
_ifconfig: name=vlan1 flags=1243 IFUP addr=(null) netmask=(null)
vlan1: No such device
_ifconfig: name=eth1 flags=1243 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=eth0 ACTION=add
hotplug net INTERFACE=eth1 ACTION=add
generate_wl_para(0x0a54): unit 1 subunit -1
num_of_mssid_support(0x0098): [mssid] support [3] mssid
generate_wl_para(0x0d54): bw: 0
generate_wl_para(0x0d56): chanspec: 0
generate_wl_para(0x0d57): bw_cap: 7
generate_wl_para(0x0d5d): obss_coex: 0
generate_wl_para(0x0a54): unit 1 subunit 1
generate_wl_para(0x0a54): unit 1 subunit 2
generate_wl_para(0x0a54): unit 1 subunit 3
eth2: cmd=14: No such device
_ifconfig: name=eth2 flags=1243 IFUP addr=(null) netmask=(null)
eth2: No such device
eth2: WLC_GET_VAR(chanspecs): No such device
failed to get valid chanspec list
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0xd92e (48u)
vlan1: cmd=14: No such device
eth2: cmd=14: No such device
Not repeater mode, do not start_wlcconnect
handle_notifications() end
[1 init:init_main +262] recv signal 14 from pid [1:/sbin/init] (from user)
[1 init:init_main +264] recv signal 14 from pid [1:/sbin/init] (from user)
[1 init:init_main +264] recv signal 14 from pid [1:/sbin/init] (from user)
[1 init:init_main +264] recv signal 14 from pid [1:/sbin/init] (from user)
<****>freeze the duck, 5s left!
813: check_action 0
813: set_action 7
813: set_action 0
calc: WIRED not found setting sync=1
calc: WIRED not found setting sync=1
calc: WIRED not found setting sync=1
update_variables: [apply] [saveNvram] [0]
value http_username=admin
value http_passwd=gozdawa
set http_passwd=gozdawa [i:httpd] 271:notify_rc chpass271: check_action 0
271: set_action 7
[1 init:init_main +358] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=chpass
[1 init:handle_notifications +358] running: 0 chpass
handle_notifications() end
271: set_action 0 [i:httpd] 271:notify_rc restart_ftpsambarestart_ftpsamba 271: waiting after 9/10.
[1 init:init_main +361] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=restart_ftpsamba
[1 init:handle_notifications +361] running: 3 ftpsamba
[1 init:start_dnsmasq +361] begin
[1 init:stop_dnsmasq +361] begin
[1 init:stop_dnsmasq +361] end
[1 init:start_dnsmasq +361] end
handle_notifications() end
[1 init:init_main +361] recv signal 14 from pid [1:/sbin/init] (from user)
271: check_action 0
271: set_action 7
271: set_action 0
apply: update_client_list httpd_check.xml
calc: WIRED not found setting sync=1
calc: WIRED not found setting sync=1
calc: WIRED not found setting sync=1
clean_mode(1) clean_time(5) threshold(22469)
free_caches: memfree=194400.
free_caches: memfree > threshold.
read from stream: 4096
image len: 15f1000
productid field in image: RT-AC66U
03 00 00 01 52 54 2d 41 43 36 36 55 00 00 00 00 00 02 02 63 00 00 00 00 00 00 00 00 00 00 00 00
## [httpd] do upgrade cgi upgrade_err(0)
restart_nas_services(1009) is skipped: test 7. [i:httpd] 271:notify_rc stop_upgrade[1 init:init_main +447] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=stop_upgrade
[1 init:handle_notifications +447] running: 1 upgrade
modem data: save the data during upgrading [i:httpd] 271:notify_rc start_upgrade271: wait for previous script(59/60): stop_upgrade 271 httpd.
restart_nas_services(1064) is skipped: test 7.
## wanduck.safeexit ##
## close 1: result=0.
## close 2: result=0.
## close 3: result=0.
## close 4: result=-1.
## close 5: result=-1.
update_wan_state(wan0_, 6, 0)
stop_auth:: done
stop_auth:: done
_ifconfig: name=eth0 flags=0000 addr=(null) netmask=(null)
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
update_wan_state(wan0_, 4, 0)
271: wait for previous script(58/60): stop_upgrade 271 httpd.
# Disable direct rule(exit wanduck)
safe_leave: apply the nat_rules(/tmp/nat_rules_eth0_eth0): nat_state=2!
# return(exit wanduck)
stop_wan_if wan0_proto=dhcp
update_wan_state(wan1_, 6, 0)
stop_auth:: done
stop_auth:: done
update_wan_state(wan1_, 4, 0)
271: wait for previous script(57/60): stop_upgrade 271 httpd.
271: wait for previous script(56/60): stop_upgrade 271 httpd.
stop_wan_if wan1_proto=dhcp
stop_misc()
killall_tk: waiting name=infosvr n=9
Aug 1 00:07:29 miniupnpd[313]: shutting down MiniUPnPd
killall_tk: waiting name=lld2d n=9
killall_tk: waiting name=rstats n=9
killall_tk: waiting name=networkmap n=9
271: wait for previous script(55/60): stop_upgrade 271 httpd.
killall_tk: waiting name=lpd n=9
killall_tk: waiting name=u2ec n=9
killall_tk: waiting name=u2ec n=8
usbcore: deregistering interface driver cdc_mbim
usbcore: deregistering interface driver cdc_ncm
usbcore: deregistering interface driver qmi_wwan
usbcore: deregistering interface driver cdc_wdm
usbcore: deregistering interface driver rndis_host
usbcore: deregistering interface driver cdc_ether
usbcore: deregistering interface driver asix
usbcore: deregistering interface driver usblp
exec_for_host(-1, 2, 16, 4781136)
271: wait for previous script(54/60): stop_upgrade 271 httpd.
ufsd: driver unloaded
271: wait for previous script(53/60): stop_upgrade 271 httpd.
usbcore: deregistering interface driver usb-storage
ohci_hcd 0000:00:04.0: remove, state 1
usb usb2: USB disconnect, address 1
ohci_hcd 0000:00:04.0: USB bus 2 deregistered
ehci_hcd 0000:00:04.1: remove, state 1
usb usb1: USB disconnect, address 1
usb 1-1: USB disconnect, address 2
ehci_hcd 0000:00:04.1: USB bus 1 deregistered
271: wait for previous script(52/60): stop_upgrade 271 httpd.
1: check_action 0
checking for user scripts: '.autostop'
handle_notifications() end
[1 init:init_main +454] recv signal 14 from pid [1:/sbin/init] (from user)
[1 init:init_main +455] recv signal 16 from pid [271:httpd] (from user)
cmd[0]=start_upgrade
[1 init:handle_notifications +455] running: 2 upgrade
vlan1: cmd=14: No such device
_ifconfig: name=eth1 flags=0000 addr=(null) netmask=(null)
br0: port 1(eth1) entering disabled state
device eth1 left promiscuous mode
br0: port 1(eth1) entering disabled state
eth2: cmd=14: No such device
hotplug net INTERFACE=eth1 ACTION=remove
hotplug net INTERFACE=eth0 ACTION=remove
hotplug_net(): sent event 1
hotplug_net(): sent event 1
[1 init:stop_dnsmasq +455] begin
killall_tk: waiting name=dnsmasq n=9
[1 init:stop_dnsmasq +455] end
Build temp rootfs
__cp: /bin/iwpriv not exist, skip!
__cp: /sbin/rtkswitch not exist, skip!
cp: can't stat '/lib/libiw*': No such file or directory
tar: empty archive
tar: short read
Write FW to the 2nd partition.
1264: check_action 0
1264: set_action 2
file len=0x15f1000
mtd size=2000000, erasesize=20000, writesize=800, type=4
freeram=acef000 unit_len=1600000 filelen=15f1000 mi.erasesize=20000 mi.writesize=800
ofs=0 n=15f1000/15f1000 ei.start=0 ei.length=1600000
1264: set_action 0
Image successfully flashed
1265: check_action 0
1265: set_action 2
file len=0x15f1000
mtd size=2000000, erasesize=20000, writesize=800, type=4
freeram=acd1000 unit_len=1600000 filelen=15f1000 mi.erasesize=20000 mi.writesize=800
ofs=0 n=15f1000/15f1000 ei.start=0 ei.length=1600000
1265: set_action 0
Image successfully flashed
switch to temp rootfilesystem
1: set_action 0
Hit ENTER for new console...
modem data: save the data during the signal 15.
disk_monitor: Finish!
killall_tk: waiting name=crond n=9
[1 init:stop_dnsmasq +473] begin
[1 init:stop_dnsmasq +473] end
killall_tk: waiting name=eapd n=9
update_wan_state(wan0_, 6, 0)
stop_auth:: done
stop_auth:: done
_ifconfig: name=eth0 flags=0000 addr=(null) netmask=(null)
eth0: No such device
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
eth0: No such device
update_wan_state(wan0_, 4, 0)
stop_wan_if wan0_proto=dhcp
update_wan_state(wan1_, 6, 0)
stop_auth:: done
stop_auth:: done
update_wan_state(wan1_, 4, 0)
stop_wan_if wan1_proto=dhcp
stop_lan 2095
_ifconfig: name=lo flags=0000 addr=(null) netmask=(null)
_ifconfig: name=br0 flags=0000 addr=(null) netmask=(null)
_ifconfig: name=vlan1 flags=0000 addr=(null) netmask=(null)
vlan1: No such device
_ifconfig: name=eth1 flags=0000 addr=(null) netmask=(null)
eth1: No such device
_ifconfig: name=eth2 flags=0000 addr=(null) netmask=(null)
eth2: No such device
[1 init:init_nvram +477] init_nvram for model(39)
num_of_mssid_support(0x0098): [mssid] support [3] mssid
update_lan_state(lan_, 4, 0)
stop_lan 2264
exec_for_host(-1, 2, 16, 4781136)
shutdn rb=1
1: check_action 0
1: set_action 8
update_wan_state(wan0_, 6, 0)
stop_auth:: done
stop_auth:: done
_ifconfig: name=eth0 flags=0000 addr=(null) netmask=(null)
eth0: No such device
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
eth0: No such device
update_wan_state(wan0_, 4, 0)
stop_wan_if wan0_proto=dhcp
update_wan_state(wan1_, 6, 0)
stop_auth:: done
stop_auth:: done
update_wan_state(wan1_, 4, 0)
stop_wan_if wan1_proto=dhcp
TERM
KILL
1
Restarting system.
Please stand by while rebooting the system...
Decompressing...done
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Null Rescue Flag.
boot the image...
Check 2 trx result: 0, 0
go load
Loader:raw Filesys:tftp Dev:(null) File:: Options:(null)
Loading: TFTP Server.
Failed.
Could not load :: Error
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 1250148 bytes read
Entry at 0x80001000
Starting program at 0x80001000
Linux version 3.10.101 (root@nmndev) (gcc version 5.1.0 (OpenWrt GCC 5.1.0 r45933) ) #12443 Mon Apr 25 09:37:11 CEST 2016
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
found nvram at 1F0000
something wrong here. do not remap
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
memory: 07fff000 @ 87fff000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x1fffffff]
HighMem [mem 0x20000000-0x8fffdfff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffefff]
node 0: [mem 0x87fff000-0x8fffdfff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64510
Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=80000de0
Readback ErrCtl register=80000de0
Cache parity protection enabled
Memory: 238976k/131068k available (3041k kernel code, 23160k reserved, 485k data, 308k init, 131068k highmem)
NR_IRQS:128
CPU: BCM5300 rev 1 at 600 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab at 0
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
cmd 6 new_cmd 6
PCI: Fixing up bridge
cmd 6 new_cmd 4
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
cmd 6 new_cmd 6
PCI: Fixing up bridge
cmd 6 new_cmd 4
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Asus-RT-AC66U init
bounce pool size: 64 pages
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 210
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
brd: module loaded
pflash: found no supported devices
try to find cfe size up to 2097152
no filesys. assume nflash devices
bootloader size: 2097152
nvram size: 65536
Creating 2 MTD partitions on "bcmsflash":
0x000000000000-0x000000200000 : "cfe"
0x0000001f0000-0x000000200000 : "nvram"
Found a Esmt NAND flash with 2048B pages or 128KB blocks; total size 128MB
NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC errorBad block table found at page 65408, version 0x01
__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC errorBad block table found at page 65344, version 0x01
nand_read_bbt: bad block at 0x000007fe0000
Creating 2 MTD partitions on "brcmnand":
0x000000000000-0x000002000000 : "linux"
0x000002000000-0x000007f00000 : "ddwrt"
lookup_nflash_rootfs_offset: offset = 0x0
found trx at 0, len =23007232
scan filesys at 131000
nflash: squash filesystem with lzma found at offset 0
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "nandimage"
0x000000131000-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
add netgear boarddata for pflash if exists
add netgear boarddata for sflash if exists
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Failed to load ipt action
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3734 buckets, 14936 max)
nf_conntrack_rtsp v0.7 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.7 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
max nvram space = 65536
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 308K (80373000 - 803c0000)
start service
starting Architecture code for broadcom
udevtrigger[747]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
boardnum J417117901
boardtype 0xF5B2
boardrev 0x1100
Booting device: Asus RT-AC66U
get_wl_instance doesnt return the right value 0
No such device
et: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
et0: etc_attach() failed
roboswitch: No such device
roboswitch: No such device
roboswitch: No such device
roboswitch: No such device
cmd 2 new_cmd 0
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
cmd 2 new_cmd 0
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
cannot open /proc/switch/eth0/reset
cannot open /proc/switch/eth0/enable_vlan
cannot open /proc/switch/eth0/vlan/1/ports
cannot open /proc/switch/eth0/vlan/2/ports
[USB] checking...
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
ifconfig: invalid hw-addr
br0: Invalid argument
br0: Invalid argument
eth1: Not supported
base addr 10:C3:7B:42:69:E4
local bit addr 12:C3:7B:42:69:E4
eth1: Invalid argument
eth1: Not supported
eth1: Operation not permitted
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
eth1: Invalid argument
enable bss eth1 0 (0)
eth1: Not supported
eth1: Not supported
wl: Unsupported
ifconfig: ioctl 0x8914 failed: Address not available
function start_hwmon not found
cannot open /proc/irq/163/smp_affinity
cannot open /proc/irq/169/smp_affinity
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts
udhcpc (v1.24.2) started
Sending discover...
Sending discover...
Radio: 0 currently turned off
Sending discover...
Radio: 1 currently turned off
Duplicate configuration request
Duplicate configuration request
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
/etc/config/conntrack.startup: line 8: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
sh: missing ]
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
killall: proxywatchdog.sh: no process killed
/mnt/smbshare
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
killall: schedulerb.sh: no process killed
Empty.
killall: wdswatchdog.sh: no process killed
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
connect: Network unreachable
connect: Network unreachable
connect: Network unreachable
gethostbyname: Resource temporarily unavailable
Sending discover...
Sending discover...
Decompressing...done
CFE version 6.30.39.29 (r338244) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 一 10月 15 10:41:41 CST 2012 (yau@wireless-pub2)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.29 (r338244)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 10-C3-7B-42-69-E0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
Check 2 trx result: 0, 0
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ... 1250148 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 3.10.101 (root@nmndev) (gcc version 5.1.0 (OpenWrt GCC 5.1.0 r45933) ) #12443 Mon Apr 25 09:37:11 CEST 2016
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
found nvram at 1F0000
something wrong here. do not remap
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
memory: 07fff000 @ 87fff000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x1fffffff]
HighMem [mem 0x20000000-0x8fffdfff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffefff]
node 0: [mem 0x87fff000-0x8fffdfff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64510
Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=80000780
Readback ErrCtl register=80000780
Cache parity protection enabled
Memory: 238976k/131068k available (3041k kernel code, 23160k reserved, 485k data, 308k init, 131068k highmem)
NR_IRQS:128
CPU: BCM5300 rev 1 at 600 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab at 0
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
cmd 6 new_cmd 6
PCI: Fixing up bridge
cmd 6 new_cmd 4
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
cmd 6 new_cmd 6
PCI: Fixing up bridge
cmd 6 new_cmd 4
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Asus-RT-AC66U init
bounce pool size: 64 pages
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 210
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
brd: module loaded
pflash: found no supported devices
try to find cfe size up to 2097152
no filesys. assume nflash devices
bootloader size: 2097152
nvram size: 65536
Creating 2 MTD partitions on "bcmsflash":
0x000000000000-0x000000200000 : "cfe"
0x0000001f0000-0x000000200000 : "nvram"
Found a Esmt NAND flash with 2048B pages or 128KB blocks; total size 128MB
NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC errorBad block table found at page 65408, version 0x01
__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC error__nand_correct_data: uncorrectable ECC error
__nand_correct_data: uncorrectable ECC errorBad block table found at page 65344, version 0x01
nand_read_bbt: bad block at 0x000007fe0000
Creating 2 MTD partitions on "brcmnand":
0x000000000000-0x000002000000 : "linux"
0x000002000000-0x000007f00000 : "ddwrt"
lookup_nflash_rootfs_offset: offset = 0x0
found trx at 0, len =23007232
scan filesys at 131000
nflash: squash filesystem with lzma found at offset 0
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "nandimage"
0x000000131000-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
add netgear boarddata for pflash if exists
add netgear boarddata for sflash if exists
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Failed to load ipt action
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3734 buckets, 14936 max)
nf_conntrack_rtsp v0.7 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.7 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
max nvram space = 65536
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 308K (80373000 - 803c0000)
start service
starting Architecture code for broadcom
udevtrigger[747]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
boardnum J417117901
boardtype 0xF5B2
boardrev 0x1100
Booting device: Asus RT-AC66U
get_wl_instance doesnt return the right value 0
No such device
et: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.89.21 (r524987)
roboswitch: Probing device 'eth0'
roboswitch: trying a 53125! at eth0
roboswitch: found a 53125! at eth0
cmd 2 new_cmd 0
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
cmd 2 new_cmd 0
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
[USB] checking...
umount: can't unmount /mnt: No such file or directory
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
ifconfig: invalid hw-addr
device br0 entered promiscuous mode
br0: Invalid argument
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
eth1: Not supported
base addr 10:C3:7B:42:69:E0
local bit addr 12:C3:7B:42:69:E0
eth1: Invalid argument
eth1: Not supported
eth1: Operation not permitted
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Argument list too long
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
eth1: Not supported
eth1: Not supported
wl: Unsupported
device eth1 entered promiscuous mode
br0: Invalid argument
eth2: Not supported
base addr 10:C3:7B:42:69:E4
local bit addr 12:C3:7B:42:69:E4
eth2: Invalid argument
eth2: Not supported
eth2: Operation not permitted
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
enable bss eth2 0 (0)
eth2: Not supported
eth2: Not supported
wl: Unsupported
device eth2 entered promiscuous mode
br0: port 3(eth2) entered forwarding state
br0: port 3(eth2) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
device br0 left promiscuous mode
cannot open /proc/irq/163/smp_affinity
cannot open /proc/irq/169/smp_affinity
function start_hwmon not found
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
device vlan2 entered promiscuous mode
cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts
device vlan2 left promiscuous mode
udhcpc (v1.24.2) started
Sending discover...
br0: port 3(eth2) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
Sending discover...
Radio: 0 currently turned off
Sending discover...
Radio: 1 currently turned off
Duplicate configuration request
Duplicate configuration request
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
/etc/config/conntrack.startup: line 8: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
sh: missing ]
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
killall: proxywatchdog.sh: no process killed
/mnt/smbshare
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
killall: schedulerb.sh: no process killed
killall: wdswatchdog.sh: no process killed
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
[APPLY] index (null) (null)
submit_button=[index] submit_type=[changepass]
name=[index] type=[changepass] service=[] sleep=[1] action=[5]
connect: Network unreachable
connect: Network unreachable
connect: Network unreachable
Sending discover...
gethostbyname: Resource temporarily unavailable
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
eth3: No such device
Sending discover...
ApplyTake:submit_button=[Management] service=[management] sleep_time=[0] action=[4]
waiting for services to finish (34)...
function stop_hwmon not found
Bad argument `80'
Try `iptables -h' or 'iptables --help' for more information.
function stop_-f not found
Duplicate configuration request
Duplicate configuration request
device vlan1 left promiscuous mode
device eth0 left promiscuous mode
br0: port 1(vlan1) entered disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entered disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entered disabled state
Duplicate configuration request
Invalid instance identifier br0
Command failed
Hooks already unregistered
Hooks already unregistered
bridge br0 is still up; can't delete it
/etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
device br0 already exists; can't create bridge with the same name
device br0 entered promiscuous mode
br0: Invalid argument
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
eth1: Not supported
base addr 10:C3:7B:42:69:E0
local bit addr 12:C3:7B:42:69:E0
eth1: Invalid argument
eth1: Not supported
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Argument list too long
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
eth1: Not supported
eth1: Not supported
wl: Unsupported
device eth1 entered promiscuous mode
br0: port 2(eth1) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: Invalid argument
wl: Not down
wl: Not down
eth2: Not supported
base addr 10:C3:7B:42:69:E4
local bit addr 12:C3:7B:42:69:E4
eth2: Invalid argument
eth2: Not supported
eth2: Operation not permitted
eth2: Invalid argument
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
br0: port 1(vlan1) entered forwarding state
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
br0: port 2(eth1) entered forwarding state
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
enable bss eth2 0 (0)
eth2: Not supported
eth2: Not supported
wl: Unsupported
Apply:submit_button=[Management] service=[management] sleep_time=[0] action=[4]
device eth2 entered promiscuous mode
br0: port 3(eth2) entered forwarding state
br0: port 3(eth2) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
device br0 left promiscuous mode
lo: File exists
cannot open /proc/irq/163/smp_affinity
cannot open /proc/irq/169/smp_affinity
function start_hwmon not found
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
device vlan2 entered promiscuous mode
cannot open /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts
device vlan2 left promiscuous mode
udhcpc (v1.24.2) started
Sending discover...
br0: port 3(eth2) entered forwarding state
Sending discover...
Radio: 0 currently turned off
Sending discover...
Radio: 1 currently turned off
Duplicate configuration request
Duplicate configuration request
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
/etc/config/conntrack.startup: line 8: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
sh: missing ]
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
killall: proxywatchdog.sh: no process killed
mkdir: can't create directory '/tmp/mnt': File exists
/mnt/smbshare
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
killall: schedulerb.sh: no process killed
killall: wdswatchdog.sh: no process killed
Sending discover...
Sending discover...
Sending discover...
wl0: No such device
wl1: No such device
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
[APPLY] Wireless_Basic (null) (null)
submit_button=[Wireless_Basic] submit_type=[save]
name=[Wireless_Basic] type=[save] service=[wireless] sleep=[1] action=[5]
wl0: No such device
wl1: No such device
Sending discover...
Sending discover...
[APPLY] Wireless_Basic (null) (null)
submit_button=[Wireless_Basic] submit_type=[save]
name=[Wireless_Basic] type=[save] service=[wireless] sleep=[1] action=[5]
device vlan1 left promiscuous mode
device eth0 left promiscuous mode
br0: port 1(vlan1) entered disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entered disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entered disabled state
Duplicate configuration request
Invalid instance identifier br0
Command failed
Hooks already unregistered
Hooks already unregistered
bridge br0 is still up; can't delete it
device br0 already exists; can't create bridge with the same name
device br0 entered promiscuous mode
br0: Invalid argument
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
eth1: Not supported
base addr 10:C3:7B:42:69:E0
local bit addr 12:C3:7B:42:69:E0
eth1: Invalid argument
eth1: Not supported
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Argument list too long
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
eth1: Not supported
enable bss eth1 0 (0)
Sending discover...
eth1: Not supported
eth1: Not supported
wl: Unsupported
device eth1 entered promiscuous mode
br0: port 2(eth1) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: Invalid argument
wl: Not down
wl: Not down
eth2: Not supported
base addr 10:C3:7B:42:69:E4
local bit addr 12:C3:7B:42:69:E4
eth2: Invalid argument
eth2: Not supported
eth2: Operation not permitted
eth2: Invalid argument
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Not supported
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
br0: port 1(vlan1) entered forwarding state
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
br0: port 2(eth1) entered forwarding state
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
eth2: Invalid argument
enable bss eth2 0 (0)
eth2: Not supported
eth2: Not supported
wl: Unsupported
device eth2 entered promiscuous mode
br0: port 3(eth2) entered forwarding state
br0: port 3(eth2) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
device br0 left promiscuous mode
lo: File exists
wl0: No such device
wl1: No such device
br0: port 3(eth2) entered forwarding state
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
wl0: No such device
wl1: No such device
Sending discover...
Sending discover...
Sending discover...
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
wl0: No such device
wl1: No such device
Sending discover...
Sending discover...
[APPLY] WL_WPATable (null) (null)
submit_button=[WL_WPATable] submit_type=[security]
name=[WL_WPATable] type=[security] service=[] sleep=[1] action=[5]
Sending discover...
[APPLY] WL_WPATable (null) (null)
submit_button=[WL_WPATable] submit_type=[security]
name=[WL_WPATable] type=[security] service=[] sleep=[1] action=[5]
Sending discover...
Sending discover...
Sending discover...
[APPLY] WL_WPATable (null) (null)
submit_button=[WL_WPATable] submit_type=[save]
name=[WL_WPATable] type=[save] service=[wireless_2] sleep=[1] action=[5]
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
eth3: No such device
Sending discover...
Sending discover...
Sending discover...
wl0: No such device
wl1: No such device
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0xce4
WARNING: at net/core/dev.c:3660 unregister_netdevice()
Call Trace:
[<8001206c>] dump_stack+0x8/0x34
[<801a8644>] unregister_netdev+0x1c/0x2c
[] et_init+0x220/0x6f4 [et]
w konsekwencji czego wifi 2.4 wykrywany jest jako eth0 (a to powinien być właśnie lan), zaś wifi 5ghz jako eth1 (a to powinno być wifi 2,4, zaś eth2 jako wifi 5ghz).
niestety nie jestem w stanie powiedzieć czemu tak się dzieje i jak to naprawić.
Proxmox VE:i5-13400T, 64GB RAM, 2x 512GB NVMe, 3x 2TB SSD, Intel X710-DA2 SFP+ VM Router:OpenWRT 22.03.4 VM NAS:Synology SA6400 VM VPS:Debian, WWW, Home Assistant Switch:Netgear MS510TXPP Switch:Ubiquiti USW-Flex-mini - szt. 2 Wi-Fi:Ubiquiti U6-Lite - szt. 2
i to jest właśnie dziwne ,ale jak wrzucę tomato to będzie działało normalnie dopóki nie wyszczyszczę nvram ręcznie za pomocą przycisków na routerze,bo aktualizując firmware z opcją czyszczenia tomato wstanie normalnie tylko że z wifi tylko 2,4gz.
Ps.
Może któryś z forumowiczów podeśle mi dla porównania cfe, może tam jest jakiś babok.
· Łącznie użytkowników: 24,115 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Maniek91PL
06-11-2024 22:37
dzięki !
maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia
Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa
overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.
maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.
overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?
maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach
maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności", więc prawdopodobnie gdzieś przepięcie.
servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.
maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
' target='_blank'>Link
null) File:: Options
