Forum: Linksys E1000v2 reanimacja brak odpowiedzi na ping

Kod Pobierz kod źródłowy



Decompressing............done

Start to blink diag led ...





CFE version 5.60.101  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)

Build Date: 08/04/10 11:22:34 CST (wzh@cybertan)

Copyright (C) 2000-2008 Broadcom Corporation.



Initializing Arena

Initializing Devices.



No DPN

This is a Serial Flash

Boot partition size = 262144(0x40000)

Found a 4MB ST compatible serial flash

Partition information:

boot    #00   00000000 -> 0003FFFF  (262144)

trx     #01   00040000 -> 0004001B  (28)

os      #02   0004001C -> 003F7FFF  (3899364)

nvram   #03   003F8000 -> 003FFFFF  (32768)

Partition information:

boot    #00   00000000 -> 0003FFFF  (262144)

trx     #01   00040000 -> 003F7FFF  (3899392)

nvram   #02   003F8000 -> 003FFFFF  (32768)

BCM47XX_GMAC_ID

et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.101

CPU type 0x19749: 300MHz

Total memory: 32768 KBytes



CFE mem:    0x80700000 - 0x807A7B00 (686848)

Data:       0x8073DC00 - 0x80740E40 (12864)

BSS:        0x80740E40 - 0x80741B00 (3264)

Heap:       0x80741B00 - 0x807A5B00 (409600)

Stack:      0x807A5B00 - 0x807A7B00 (8192)

Text:       0x80700000 - 0x8073DBFC (252924)



Boot version: v5.1.6

The boot is CFE

mac_init(): Find mac [98:fc:11:88:2a:28] in location 0

Nothing...

CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]

Device eth0:  hwaddr 98-FC-11-88-2A-28, ipaddr 192.168.1.1, mask 255.255.255.0

        gateway not set, nameserver not set

CMD: [go;]

Check CRC of image1



 Err invalid Boot magic 808464709 810697800

Invalid boot block on disk

CMD: [flash -ctheader : flash1.trx]

Reading :: _tftpd_open(): retries=0/3

_tftpd_open(): retries=1/3

_tftpd_open(): retries=2/3

Failed.: Timeout occured

CMD: [flash -ctheader : flash1.trx]

Reading :: _tftpd_open(): retries=0/3

_tftpd_open(): retries=1/3

_tftpd_open(): retries=2/3

Kod Pobierz kod źródłowy



Decompressing............done

Start to blink diag led ...





CFE version 5.60.101  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)

Build Date: 08/04/10 11:22:34 CST (wzh@cybertan)

Copyright (C) 2000-2008 Broadcom Corporation.



Initializing Arena

Initializing Devices.



No DPN

This is a Serial Flash

Boot partition size = 262144(0x40000)

Found a 4MB ST compatible serial flash

Partition information:

boot    #00   00000000 -> 0003FFFF  (262144)

trx     #01   00040000 -> 0004001B  (28)

os      #02   0004001C -> 003F7FFF  (3899364)

nvram   #03   003F8000 -> 003FFFFF  (32768)

Partition information:

boot    #00   00000000 -> 0003FFFF  (262144)

trx     #01   00040000 -> 003F7FFF  (3899392)

nvram   #02   003F8000 -> 003FFFFF  (32768)

BCM47XX_GMAC_ID

et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.101

CPU type 0x19749: 300MHz

Total memory: 32768 KBytes



CFE mem:    0x80700000 - 0x807A7B00 (686848)

Data:       0x8073DC00 - 0x80740E40 (12864)

BSS:        0x80740E40 - 0x80741B00 (3264)

Heap:       0x80741B00 - 0x807A5B00 (409600)

Stack:      0x807A5B00 - 0x807A7B00 (8192)

Text:       0x80700000 - 0x8073DBFC (252924)



Boot version: v5.1.6

The boot is CFE

mac_init(): Find mac [98:fc:11:88:2a:28] in location 0

Nothing...

CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]

Device eth0:  hwaddr 98-FC-11-88-2A-28, ipaddr 192.168.1.1, mask 255.255.255.0

        gateway not set, nameserver not set

Automatic startup canceled via Ctrl-C / ESC

Stop to blink diag led ...CFE> ^C

CFE>

CFE> help
CMD: [help]
Available commands:

upgrade Upgrade Firmware
et Broadcom Ethernet utility.
modify Modify flash data.
nvram NVRAM utility.
reboot Reboot.
flash Update a flash memory device
memtest Test memory.
f Fill contents of memory.
e Modify contents of memory.
d Dump memory.
u Disassemble instructions.
batch Load a batch file into memory and execute it
go Verify and boot OS image.
boot Load an executable file into memory and execute it
load Load an executable file into memory without executing it
save Save a region of memory to a remote file via TFTP
ping Ping a remote IP host.
arp Display or modify the ARP Table
ifconfig Configure the Ethernet interface
show clocks Show current values of the clocks.
show heap Display information about CFE's heap
show memory Display the system physical memory map.
show devices Display information about the installed devices.
unsetenv Delete an environment variable.
printenv Display the environment variables
setenv Set an environment variable.
help Obtain help for CFE commands