Przeczytałem już chyba wszystkie wątki na forum , jednak mam duży problem z konfiguracją.
Kupiłem ASUS gp v1 i modem Speedstream 4100 dialog.
Wchodzę na modem , dla sprawdzenia konfiguruję mu łącze dla netii na kablach TP :
0/35 VCMUX , login i hasło,zapisuję ustawienia i reboot i niestety - nie świeci dioda DSL ani internet.
Czy jest możliwe że modemik jest padnięty ?
Mam jeszcze speedtoucha 330 , jak nie będzie działał Siemens ,tobym go podłączył ale niestety nie umiem znaleźć driverów do niego dla Kamikadze rc1 .
Są jakieś drivery ? A jeśli tak to jak je zainstalować ręcznie w asusie na wspomnianym wcześniej oprogramowaniu .
Jeśli to możliwe , to proszę o szybką pomoc
Ok , więc wgram rc2 ale jak to zainstalować w asusie bez możliwości podłączenia go to netu ?
Czy jest możliwe że ten siemens jest na inny anex niż A ? a może to zależy od firmware i dzięki panie adminie za pomoc
Ps. NA jądrze 2.4 czy 2.6 ?
Edytowany przez pca dnia 29-01-2009 17:27
Bo to downloads.openwrt.org jest
[url]
http://downloads.openwrt.org/kamikaze/8.09_RC2/brcm47xx/packages/kmod-usb-atm-speedtouch_2.6.25.17-brcm47xx-1_mipsel.ipk[/url] http://downloads.openwrt.org/kamikaze...mipsel.ipk
ten rc2 cały czas był taki okrojony ? wszedłem przez interfejs graficzny a tam 3 zakładki tylko owerview , network ,system.
Co jeszcze zainstalować jeszcze ? nie ma zakładki wan ani lan
Nie świecą diody na modemie po podłączeniu do asusa , dlaczego ?
poniżej to co udało i się skopiować z logread
(order: 2, 16384 bytes)
Jan 20 12:46:00 OpenWrt user.info kernel: Inode-cache hash table entries: 2048 ( order: 1, 8192 bytes)
Jan 20 12:46:00 OpenWrt user.info kernel: Memory: 29808k/32768k available (2082k kernel code, 2960k reserved, 315k data, 128k init, 0k highmem)
Jan 20 12:46:00 OpenWrt user.debug kernel: Calibrating delay loop... 263.16 Bogo MIPS (lpj=526336)
Jan 20 12:46:00 OpenWrt user.warn kernel: Mount-cache hash table entries: 512
Jan 20 12:46:00 OpenWrt user.info kernel: net_namespace: 540 bytes
Jan 20 12:46:00 OpenWrt user.info kernel: NET: Registered protocol family 16
Jan 20 12:46:00 OpenWrt user.debug kernel: Switched to high resolution mode on C PU 0
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: PCIcore in host mode found
Jan 20 12:46:00 OpenWrt user.info kernel: Registering a PCI bus after boot
Jan 20 12:46:00 OpenWrt user.info kernel: PCI: Fixing up bridge 0000:00:00.0
Jan 20 12:46:00 OpenWrt user.debug kernel: PCI: Setting latency timer of device 0000:00:00.0 to 64
Jan 20 12:46:00 OpenWrt user.info kernel: PCI: Fixing up device 0000:00:00.0
Jan 20 12:46:00 OpenWrt user.info kernel: PCI: Fixing latency timer of device 00 00:00:00.0 to 168
Jan 20 12:46:00 OpenWrt user.warn kernel: PCI: Enabling device 0000:00:02.0 (000 0 -> 0002)
Jan 20 12:46:00 OpenWrt user.info kernel: PCI: Fixing up device 0000:00:02.0
Jan 20 12:46:00 OpenWrt user.debug kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: Core 0 found: ChipCommon (cc 0x80 0, rev 0x0D, vendor 0x4243)
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: Core 1 found: IEEE 802.11 (cc 0x8 12, rev 0x09, vendor 0x4243)
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: Core 3 found: PCMCIA (cc 0x80D, r ev 0x07, vendor 0x4243)
Jan 20 12:46:00 OpenWrt user.debug kernel: ssb: SPROM revision 2 detected.
Jan 20 12:46:00 OpenWrt user.info kernel: ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
Jan 20 12:46:00 OpenWrt user.info kernel: NET: Registered protocol family 2
Jan 20 12:46:00 OpenWrt user.info kernel: IP route cache hash table entries: 102 4 (order: 0, 4096 bytes)
Jan 20 12:46:00 OpenWrt user.info kernel: TCP established hash table entries: 10 24 (order: 1, 8192 bytes)
Jan 20 12:46:00 OpenWrt user.info kernel: TCP bind hash table entries: 1024 (ord er: 0, 4096 bytes)
Jan 20 12:46:00 OpenWrt user.info kernel: TCP: Hash tables configured (establish ed 1024 bind 1024)
Jan 20 12:46:00 OpenWrt user.info kernel: TCP reno registered
Jan 20 12:46:00 OpenWrt user.notice kernel: detected lzma initramfs
Jan 20 12:46:00 OpenWrt user.notice kernel: initramfs: LZMA lc=1,lp=2,pb=2,origS ize=512
Jan 20 12:46:00 OpenWrt user.info kernel: squashfs: version 3.0 (2006/03/15) Phi llip Lougher
Jan 20 12:46:00 OpenWrt user.warn kernel: Registering mini_fo version $Id$
Jan 20 12:46:00 OpenWrt user.info kernel: JFFS2 version 2.2. (NAND) (SUMMARY) Â Š 2001-2006 Red Hat, Inc.
Jan 20 12:46:00 OpenWrt user.info kernel: io scheduler noop registered
Jan 20 12:46:00 OpenWrt user.info kernel: io scheduler deadline registered (defa ult)
Jan 20 12:46:00 OpenWrt user.info kernel: Serial: 8250/16550 driver $Revision: 1 .90 $ 2 ports, IRQ sharing enabled
Jan 20 12:46:00 OpenWrt user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 3 ) is a 16550A
Jan 20 12:46:00 OpenWrt user.info kernel: serial82
Jan 20 12:46:00 OpenWrt user.info kernel: 50: ttyS1 at MMIO 0x0 (irq = 3) is a 1 6550A
Jan 20 12:46:00 OpenWrt user.err kernel: serial8250 serial8250.0: unable to regi ster port at index 0 (IO0 MEMb8000300 IRQ3): -28
Jan 20 12:46:00 OpenWrt user.err kernel: serial8250 serial8250.0: unable to regi ster port at index 1 (IO0 MEMb8000400 IRQ3): -28
Jan 20 12:46:00 OpenWrt user.info kernel: b44.c:v2.0
Jan 20 12:46:00 OpenWrt user.info kernel: eth0: Broadcom 44xx/47xx 10/100BaseT E thernet 00:22:15:12:38:c7
Jan 20 12:46:00 OpenWrt user.err kernel: b44: eth1: PHY Reset would not complete .
Jan 20 12:46:00 OpenWrt user.info kernel: eth1: Broadcom 44xx/47xx 10/100BaseT E thernet 40:10:18:00:00:2d
Jan 20 12:46:00 OpenWrt user.warn kernel: flash init: 0x1c000000 0x02000000
Jan 20 12:46:00 OpenWrt user.info kernel: Physically mapped flash: Found 1 x16 d evices at 0x0 in 16-bit bank
Jan 20 12:46:00 OpenWrt user.debug kernel: Physically mapped flash: Found an ali as at 0x800000 for the chip at 0x0
Jan 20 12:46:00 OpenWrt user.debug kernel: Physically mapped flash: Found an ali as at 0x1000000 for the chip at 0x0
Jan 20 12:46:00 OpenWrt user.debug kernel: Physically mapped flash: Found an ali as at 0x1800000 for the chip at 0x0
Jan 20 12:46:00 OpenWrt user.warn kernel: Amd/Fujitsu Extended Query Table at 0 x0040
Jan 20 12:46:00 OpenWrt user.warn kernel: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan 20 12:46:00 OpenWrt user.notice kernel: number of CFI chips: 1
Jan 20 12:46:00 OpenWrt user.notice kernel: cfi_cmdset_0002: Disabling erase-sus pend-program due to code brokenness.
Jan 20 12:46:00 OpenWrt user.notice kernel: Flash device: 0x800000 at 0x1fc00000
Jan 20 12:46:00 OpenWrt user.notice kernel: bootloader size: 262144
Jan 20 12:46:00 OpenWrt user.notice kernel: Creating 4 MTD partitions on "Physic ally mapped flash":
Jan 20 12:46:00 OpenWrt user.notice kernel: 0x00000000-0x00040000 : "cfe"
Jan 20 12:46:00 OpenWrt user.notice kernel: 0x00040000-0x007f0000 : "linux"
Jan 20 12:46:00 OpenWrt user.notice kernel: 0x000fe400-0x007f0000 : "rootfs"
Jan 20 12:46:00 OpenWrt user.warn kernel: mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
Jan 20 12:46:00 OpenWrt user.notice kernel: mtd: partition "rootfs" set to be ro ot filesystem
Jan 20 12:46:00 OpenWrt user.info kernel: mtd: partition "rootfs_data" created a utomatically, ofs=290000, len=560000
Jan 20 12:46:00 OpenWrt user.notice kernel: 0x00290000-0x007f0000 : "rootfs_data "
Jan 20 12:46:00 OpenWrt user.notice kernel: 0x007f0000-0x00800000 : "nvram"
Jan 20 12:46:00 OpenWrt user.info kernel: TCP vegas registered
Jan 20 12:46:00 OpenWrt user.info kernel: NET: Registered protocol family 1
Jan 20 12:46:00 OpenWrt user.info kernel: NET: Registered protocol family 17
Jan 20 12:46:00 OpenWrt user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear
Jan 20 12:46:00 OpenWrt user.info kernel: All bugs added by David S. Miller
Jan 20 12:46:00 OpenWrt user.warn kernel: VFS: Mounted root (squashfs filesystem ) readonly.
Jan 20 12:46:00 OpenWrt user.info kernel: Freeing unused kernel memory: 128k fre ed
Jan 20 12:46:00 OpenWrt user.warn kernel: Please be patient, while OpenWrt loads ...
Jan 20 12:46:00 OpenWrt user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 20 12:46:00 OpenWrt user.warn kernel: diag: Detected 'ASUS WL-500g Premium'
Jan 20 12:46:00 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, ful l duplex.
Jan 20 12:46:00 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Jan 20 12:46:00 OpenWrt user.info kernel: roboswitch: Probing device eth0: found !
Jan 20 12:46:00 OpenWrt user.info kernel: b44: eth0: powering down PHY
Jan 20 12:46:00 OpenWrt user.info kernel: mini_fo: using base directory
Jan 20 12:46:00 OpenWrt user.info kernel: mini_fo: using storage directoryjff s
Jan 20 12:46:01 OpenWrt user.info kernel: b44: eth0: Link is up at 100 Mbps, ful l duplex.
Jan 20 12:46:01 OpenWrt user.info kernel: b44: eth0: Flow control is off for TX and off for RX.
Jan 20 12:46:03 OpenWrt user.err kernel: br-lan: Dropping NETIF_F_UFO since no N ETIF_F_HW_CSUM feature.
Jan 20 12:46:03 OpenWrt user.info kernel: device eth0.0 entered promiscuous mode
Jan 20 12:46:03 OpenWrt user.info kernel: device eth0 entered promiscuous mode
Jan 20 12:46:03 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering learni ng state
Jan 20 12:46:03 OpenWrt user.info kernel: br-lan: topology change detected, prop agating
Jan 20 12:46:03 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering forwar ding state
Jan 20 12:46:04 OpenWrt user.info kernel: usbcore: registered new interface driv er usbfs
Jan 20 12:46:04 OpenWrt user.info kernel: usbcore: registered new interface driv er hub
Jan 20 12:46:04 OpenWrt user.info kernel: usbcore: registered new device driver usb
Jan 20 12:46:04 OpenWrt user.info kernel: NET: Registered protocol family 8
Jan 20 12:46:04 OpenWrt user.info kernel: NET: Registered protocol family 20
Jan 20 12:46:05 OpenWrt user.info kernel: b43-phy0: Broadcom 4318 WLAN found
Jan 20 12:46:05 OpenWrt user.debug kernel: b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
Jan 20 12:46:05 OpenWrt user.debug kernel: b43-phy0 debug: Found Radio: Manuf 0x 17F, Version 0x2050, Revision 8
Jan 20 12:46:05 OpenWrt user.debug kernel: b43-phy0 debug: DebugFS (CONFIG_DEBUG _FS) not enabled in kernel config
Jan 20 12:46:05 OpenWrt user.debug kernel: phy0: Selected rate control algorithm 'pid'
Jan 20 12:46:05 OpenWrt user.info kernel: Broadcom 43xx driver loaded [ Features : NLR, Firmware-ID: FW13 ]
Jan 20 12:46:05 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering disabl ed state
Jan 20 12:46:05 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering learni ng state
Jan 20 12:46:05 OpenWrt user.info kernel: br-lan: topology change detected, prop agating
Jan 20 12:46:05 OpenWrt user.info kernel: br-lan: port 1(eth0.0) entering forwar ding state
Jan 20 12:46:05 OpenWrt user.info kernel: PPP generic driver version 2.4.2
Jan 20 12:46:06 OpenWrt user.info kernel: ip_tables: (C) 2000-2006 Netfilter Cor e Team
Jan 20 12:46:07 OpenWrt user.warn kernel: nf_conntrack version 0.5.0 (1024 bucke ts, 4096 max)
Jan 20 12:46:07 OpenWrt user.info kernel: usbcore: registered new interface driv er speedtch
Jan 20 12:46:08 OpenWrt user.info : 'wlan0' is disabled
Jan 20 12:46:08 OpenWrt user.info : 'wlan0' is disabled
Jan 20 12:46:09 OpenWrt user.info : Loading defaults
Jan 20 12:46:09 OpenWrt user.info : Loading synflood protection
Jan 20 12:46:09 OpenWrt user.info : Adding custom chains
Jan 20 12:46:10 OpenWrt user.info : Loading zones
Jan 20 12:46:10 OpenWrt user.info : Loading rules
Jan 20 12:46:10 OpenWrt user.info : Loading forwarding
Jan 20 12:46:10 OpenWrt user.info : Loading redirects
Jan 20 12:46:10 OpenWrt user.info : Loading includes
Jan 20 12:46:11 OpenWrt user.notice root: adding lan (br-lan) to firewall zone l an
Jan 20 12:46:12 OpenWrt authpriv.info dropbear[749]: Running in background
Jan 20 12:46:16 OpenWrt daemon.info dnsmasq[781]: started, version 2.46 cachesiz e 150
Jan 20 12:46:16 OpenWrt daemon.info dnsmasq[781]: compile time options: IPv6 GNU -getopt no-DBus no-I18N TFTP
Jan 20 12:46:16 OpenWrt daemon.info dnsmasq[781]: DHCP, IP range 192.168.1.100 - - 192.168.1.250, lease time 12h
Jan 20 12:46:16 OpenWrt daemon.info dnsmasq[781]: using local addresses only for domain lan
Jan 20 12:46:16 OpenWrt daemon.warn dnsmasq[781]: no servers found in /tmp/resol v.conf.auto, will retry
Jan 20 12:46:16 OpenWrt daemon.info dnsmasq[781]: read /etc/hosts - 1 addresses
Jan 20 12:46:16 OpenWrt daemon.err dnsmasq[781]: failed to read /etc/ethers:No s uch file or directory
Jan 20 12:46:28 OpenWrt authpriv.info dropbear[789]: Child connection from 192.1 68.1.100:2165
Jan 20 12:46:41 OpenWrt authpriv.notice dropbear[789]: password auth succeeded f or 'root' from 192.168.1.100:2165
Jan 20 12:49:17 OpenWrt authpriv.info dropbear[797]: Child connection from 192.1 68.1.100:2170
Jan 20 12:49:23 OpenWrt authpriv.notice dropbear[797]: password auth succeeded f or 'root' from 192.168.1.100:2170
Jan 20 12:50:13 OpenWrt authpriv.info dropbear[817]: Child connection from 192.1 68.1.100:2171
Jan 20 12:50:19 OpenWrt authpriv.notice dropbear[817]: password auth succeeded f or 'root' from 192.168.1.100:2171
Jan 20 12:50:49 OpenWrt daemon.info pppd[852]: Plugin pppoatm.so loaded.
Jan 20 12:50:49 OpenWrt daemon.notice pppd[853]: pppd 2.4.3 started by root, uid 0
Jan 20 12:50:49 OpenWrt daemon.err pppd[853]: connect(0.35): No such device
Jan 20 12:50:49 OpenWrt daemon.info pppd[853]: Exit.
root@OpenWrt:~#
@obsy zaczyna juz coś chyba działać
Niemniej jednak dalej nie mam netu i nie wiem dlaczego.
Może ustawienia karty sieciowej w kompie ?
komp ip 192.168.1.100
maska 255.255.255.0
brama 192.168.1.1
dns 192.168.1.1
Jeszcze jedno , w konfigu z "wan" ustawiłem mu vc-mux zamiast llc - dobrze zrobiłem ?
Poniżej logi aktualne
root@OpenWrt:~# dmesg
Linux version 2.6.25.17 (nbd@baustelle) (gcc version 4.1.2) #9 Wed Jan 21 03:52: 12 CET 2009
console [early0] enabled
CPU revision is: 00029006 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x02, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x00, vendor 0x4243)
ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x00, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 2 => 2
ssb: set_irq: core 0x0806, irq 3 => 3
ssb: set_irq: core 0x0804, irq 0 => 4
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0 -> 8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 8192
On node 0 totalpages: 8192
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/pre init noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29808k/32768k available (2082k kernel code, 2960k reserved, 315k data, 1 28k init, 0k highmem)
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
net_namespace: 540 bytes
NET: Registered protocol family 16
Switched to high resolution mode on CPU 0
ssb: PCIcore in host mode found
Registering a PCI bus after boot
PCI: Fixing up bridge 0000:00:00.0
PCI: Setting latency timer of device 0000:00:00.0 to 64
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:02.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
ssb: SPROM revision 2 detected.
ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Š 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMb8000300 IRQ 3): -28
serial8250 serial8250.0: unable to register port at index 1 (IO0 MEMb8000400 IRQ 3): -28
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:22:15:12:38:c7
b44: eth1: PHY Reset would not complete.
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:10:18:00:00:2d
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x000fe400-0x007f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o nly
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=290000, len=560000
0x00290000-0x007f0000 : "rootfs_data"
0x007f0000-0x00800000 : "nvram"
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'ASUS WL-500g Premium'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
mini_fo: using base directory
mini_fo: using storage directoryjffs
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
b43-phy0: Broadcom 4318 WLAN found
b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8
b43-phy0 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: NLR, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
br-lan: port 1(eth0.0) entering disabled state
br-lan: port 1(eth0.0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.0
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.1
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:03.2
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:03.2: irq 6, io mem 0x40002000
usb 1-1: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 3-0:1.0: unable to enumerate USB device on port 1
usbcore: registered new interface driver speedtch
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: reset full speed USB device using uhci_hcd and address 3
speedtch 1-1:1.0: found stage 1 firmware speedtch-1.bin.4
speedtch 1-1:1.0: found stage 2 firmware speedtch-2.bin.4
ATM dev 0: ADSL line is synchronising
ATM dev 0: ADSL line is down
ATM dev 0: ADSL line is synchronising
ATM dev 0: ADSL line is up (1312 kb/s down | 320 kb/s up)
root@OpenWrt:~#
root@OpenWrt:~# ifconfig
br-lan Link encap:Ethernet HWaddr 00:22:15:12:38:C7
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:113 errors:0 dropped:0 overruns:0 frame:0
TX packets:85 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8277 (8.0 KiB) TX bytes:20116 (19.6 KiB)
· Łącznie użytkowników: 24,115 · Najnowszy użytkownik: Ja
Czat
Musisz się zalogować, aby opublikować wiadomość.
Maniek91PL
06-11-2024 22:37
dzięki !
maxikaaz
29-10-2024 14:27
@Maniek91PL - Administration=> Admin Access, i tam masz "Allow Wireless Access" do zaznaczenia
Maniek91PL
26-10-2024 22:07
siemka! ktoś przypomni co się ustawiało jeśli nie mogę wejść od strony wifi do tomato? od lan działa
overflow2
04-10-2024 17:34
Kupowałem Asusy n10u albo n12d1 ale nie widzę ich, chyba już nie produkują, Chodzi o coś nowego i taniego. Transfery niewielkie.
maxikaaz
04-10-2024 09:38
@overflow2 patrząc po dostępności funkcji w nowych kompilacjach, to chyba nawet WRT54G/GL jeszcze ma OpenVPN, albo jakiś odpowiednik... zależy, na jakie transfery liczysz.
overflow2
30-09-2024 20:53
Jaki aktualnie najtańszy router do tomato do openvpn?
maxikaaz
27-07-2024 15:07
@servee - na początek router do rozebrania i obejrzenia, ciężko wróżyć tak tylko po objawach
maxikaaz
27-07-2024 14:55
@servee - cały kontroler nie pada tak sobie z powodu "zbiegu okoliczności", więc prawdopodobnie gdzieś przepięcie.
servee
25-07-2024 13:33
@maxikaaz: działało, aż pewnego pięknego dnia przestało działać. W tym dniu była też burza, ale to raczej zbieg okoliczności.
maxikaaz
25-07-2024 11:38
@servee - o ile problem jest w obrębie samych wyjść (dławiki, warystory), to naprawialne, ale jeśli w samym SoC - to nienaprawialne ze względu na koszta. A co było przyczyną?
' target='_blank'>Link
