Sprawdź jeszcze wersję EN, może w PL jest coś nie tak.

Sprawdziłem to na wersji v105 PL co była udostępniona przed padnięciem strony. Zgłaszałem problem.



Sprawdzał to inny użytkownik i stwierdził po teście, że problem występuje tylko w wersji PL.

I właśnie dlatego ja używam tylko EN

Na wersji "Tomato Firmware 1.28.0000 MIPSR2-105 K26 USB Big-VPN" EN adresy MAC również są nieprawidłowe.

Robiłem czyszczenie.

Witam , ja mam pytanie z innej beczki
Czy udalo sie komus uruchomic film MKV ze sciezka dzwiekowa DTS na minidlna tego z Tomato ? dodam tylko ze na Mezzmo udostepnionego przez Windowsa DTS pieknie chodzi , do pelni szczescia oprogramowania tomato brakuje mi tylko obslugi DTS...a moze na jakims innym progsie uda sie ta sztuka? Dzieki i pozdrawiam Wszystkich!

Na XDA sa biblioteki do MX Playera właśnie z kodekiem DTS. Moze mozna by je przekompilowac i dodac do Tomato jako moduły?

any chance to install mono on this firmware?
thx.

mono? Do you mean .NET framework support??

yes shibby.I need it to run a app wich req mono.

OMG dotnet app on router? :/ i dont see this :/ For mono you need Apache2 (i dont hear about mono module for lighttpd) + full php support. IMO it`s too big for router.

WRT54G
po zmianie z 104 ND-VPN na 105 ND-VPN dzialajacy wczesniej OpenVPN wyklada sie z bledem :
Jan 24 21:02:40 mars user.info kernel: Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Jan 24 21:02:40 mars user.info init[1]: VPN_LOG_ERROR: 141: Creating tunnel interface failed...

No, apache2 is not necessary. And apparently the current version of mono supports mips architecture:
http://www.mono-project.com/Mono:MIPS

I have found a few interesting links:
http://stackoverflow.com/questions/36...r-hardware

Apparently one can compile mono with tools from ipkg:
http://blog.hexad.dk/2012/03/mono-on-...s-211.html (although this is arm arch)

Here it says that with correct configuration it can fit within 32MB RAM:
http://www.mono-project.com/Small_foo..._footprint

And here someone claims they compiled mono for Popcorn Hour A300 which is a media player with smp8647 processor (MIPS arch, found in some routerboards)
http://www.networkedmediatank.com/sho...?tid=59383

The biggest problem is probably compiling against uclibc, but I have found reports of people doing that, but not straightforward instructions.

To sum up, most probably this will not run acceptably for any practical purposes, but it might be a fun experiment :-)

W wersji 105 nastąpiła Aktualizacja OpenVPN do wersji 2.3.0 sprawdź czy twój klient jest odpowiednio Świerzy.

zgłaszano mi to na K24. Na k26 jest ok bo sam używam. Więcej logów nie ma?

Potestuję to.

hi, my asus rt-n16 add the 5G wifi card but sometimes it could not reboot, this time must be turn the power off. please help me!!
the ttl message:
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: :74; 5る 27 16:47:24 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.3
CPU type 0x19740: 480MHz
Tot mem: 131072 KBytes

CFE mem: 0x80700000 - 0x8079B310 (635664)
Data: 0x80731B30 - 0x80734880 (11600)
BSS: 0x80734880 - 0x80735310 (2704)
Heap: 0x80735310 - 0x80799310 (409600)
Stack: 0x80799310 - 0x8079B310 (8192)
Text: 0x80700000 - 0x80731B30 (203568)

Committing NVRAM...done
Waiting for reset button release...done

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: :74; 5る 27 16:47:24 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.3
CPU type 0x19740: 480MHz
Tot mem: 131072 KBytes

CFE mem: 0x80700000 - 0x8079B310 (635664)
Data: 0x80731B30 - 0x80734880 (11600)
BSS: 0x80734880 - 0x80735310 (2704)
Heap: 0x80735310 - 0x80799310 (409600)
Stack: 0x80799310 - 0x8079B310 (8192)
Text: 0x80700000 - 0x80731B30 (203568)

Device eth0: hwaddr CC-AE-C5-C4-14-CC, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 5192 bytes read
Entry at 0x80001000
Starting program at 0x80001000
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #2 Thu Jan 10 12:51:12 CST 2013
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32767
HighMem 32767 -> 32767
early_node_map[1] active PFN ranges
0: 0 -> 32767
Built 1 zonelists. Total pages: 32767
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 pkg 10 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126620k/131068k available (33k kernel code, 4312k reserved, 2786k data, 128k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: no core
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x01fe0000 : "linux"
0x0012cc00-0x00980000 : "rootfs"
0x00980000-0x01fe0000 : "jffs2"
0x01fe0000-0x02000000 : "nvram"
Found an serial flash with 0 0KB blocks; total size 0MB
sflash: found no supported devices
_nvram_init: allocat header: 2280652800, size= 65536
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo , http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Jan 10 2013 11:42:09]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Warning: unable to open an initial console.
emf: module license 'Proprietary' taints kernel.
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.20
wl_module_init: passivemode set to 0x0
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.100.138.20
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
Data bus error, epc == 80153298, ra == 80153904
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 00010010 11009c03
$ 4 : 876acc00 00000001 00000400 00000000
$ 8 : 0c0800d0 0c0800d3 00000004 876abf1c
$12 : 00200200 87ffc388 87ffc390 00000000
$16 : 876ba600 0000432b 876acc00 00000001
$20 : 18001000 a8008000 00000001 00000001
$24 : 00000010 00000000
$28 : 87c5a000 87c5baa0 a8008000 80153904
Hi : e683d620
Lo : e00762f7
epc : 80153298 Tainted: P
ra : 80153904 Status: 11009c03 KERNEL EXL IE
Cause : 4000801c
PrId : 00019740
Modules linked in: wl(P) dnsmq(P) et(P) igs(P) emf(P)
Process modprobe (pid: 295, threadinfo=87c5a000, task=8114c800)
Stack : 00000001 800fe2d4 00000000 00000080 00000008 87c5bae0 00000000 18000000
00010010 00000680 00000009 87c5bae8 8014c124 0000432b 87c5bae0 8000fcb8
02800001 802ee8c8 00010010 87c5bb08 000000d0 fffffffc 00000010 876ba600
8014d44c 800fe3f4 02800001 00000000 0000432b 876acc00 876ba600 0000432b
876acc00 00000001 18001000 87c5bb50 801531fc 00000000 876ba600 0000432b
...
Call Trace:[][][][][][][][][][][][<80003204>][<80003204>]

Code: 3c15b800 0000000f 8ea20000 0000000f 8fa20018 7c461d00 00021f02 3044ffff

Tyle że tworzenie interfejsu wykłada się na routerze, openvpn nie inicjuje się.
Dotyczy to tak klienta jak i serwera (wciąż mówiąc wyłącznie o linksysie).

a zobacz czy moduł tun ci się ładuje

wyglada,ze sie nie laduje:
ipt_recent 8224 2
ipt_IMQ 672 0 (unused)
imq 2688 0 (unused)
ip_nat_pptp 2092 0 (unused)
ip_conntrack_pptp 2716 1
ip_nat_proto_gre 1136 0 (unused)
ip_conntrack_proto_gre 2328 0 [ip_nat_pptp ip_conntrack_pptp]
ip_nat_ftp 2928 0 (unused)
ip_conntrack_ftp 4032 1
ip_nat_h323 2120 0 (unused)
ip_conntrack_h323 2536 1
ip_nat_rtsp 5616 0 (unused)
ip_conntrack_rtsp 4776 1
wl 897168 0 (unused)
et 28920 0 (unused)

Witam!

Wgrałem do RT-N12 nową wersję Tomato v105 PL
Wszystko poszło OK, ale na zakładce Sieci wirtualne WiFi nie można zapisać ustawień.
Ten błąd nie występuje w angielskiej wersji v105

Juz wiem w czym problem z ovpn w k24. Brakuje jednej biblioteki libresolv.
Badam problem