R7000 + tomato 132 K26ARM USB AIO-64K na łączu 250/20 śmiga jak złoto ( z CFT i bez - nie zauważam róznicy)

i have rt56u router.
everytime when i reboot my router, usb3.0 flash, not mounted at all!!!
this was and in older firmware.

to fix that, i turn off/on Core USB Support and flash will be visible in attached devices. but still not mounted. i reboot router, and if luck with me, usb3.0 will mounted correctly. if not, i reboot one more time.

this very bad.

why it is happend ?
may be fix is ?

@vf... how are you mounting usb3.0 flash? I hope you are not using Automount

try to mount device puting command in scripts > firewall

yes, i'm use automount.
why it is bad ?

thanks i'm trying your method to mount.

Połączony z 12 marzec 2016 15:36:39:
no. it is not working.
because, my usbflash not visible in /dev like any sda1,2,3 (3 partions)
after turn off/on core usb support, /dev/sda - become visible, but no one partitions.
after reboot router all ok. and automounting - fine works too.

what file system are you using? ext3/4? For router you should not use NTFS or FAT

if you have enable please disable usb1.1 support

do you have USB3.0 flash connected to router via usb3.0 or 2.0 usb port?

it is possibile that your device require a lot of power and this is the reason that sometimes it is recognized or not - did you tryied to use active (with outside power sorce) usb hub? You can try to turn off all function like wi-fi etc to see if then USB pen will work if yes for sure you just need to use additional power sorce like active hub.

automounting is bad way to do that for me this function should not exist at all

usb3.0 with ext3 file system
usb1.1 is disabled everytime at all.
i connect usb3.0 flash via usb3.0 port.
if I'm connect this flash via usb2.0 it work perfectly, but i need more speed.
i'm use usb3.0 flash 32Gb. not portable hdd.

try connect your device using active usb3.0 hub

i'm no have usb3.0 hub

when i restart router, ls /dev have no 2-1 device, sda(1,2,3) and usbdev2.2
when i turn off/on core usb support, 2-1 device and usbdev2.2 and sda(not 1,2,3 just sda) will be shown in /dev
nothing to mount.

when i restart router again, it is to be ok mounted and work fine maybe month or two, while i'm not restart it again.

Połączony z 12 marzec 2016 17:38:15:
i see blink and blink_5g process in runtime, but only power led shining.

Could you please explain why do we need to put these commands to the "scripts > firewall" but not "Init"? What is the difference?

It was explained long time ago by Shibby. "Init" is execute 1st and is possible that not all modules will be on when you will try to mount HDD therefore "firewall" tab should be used.

In this post Shibby says something completely different.

ok I need to modify it than but I did not had any issue with it before. It is good that evryday I am learning something new.

Czy nowe Tomato by Shibby v133/134 ma wdudowany adblock?

nie, jeszcze nie zakończyłem prac nad tą funkcjonalnością.

Pewnie będzie w nowym, obiecanym v.135

w v135 nie będzie jeszcze adblocka wbudowanego.

v135 właśnie się kompiluje i będzie poprawionym v134 jeżeli chodzi o MultiWANa. Nic więcej.

To może lepiej poczekać jeszcze ten tydzień i zaktualizować za jednym razem

Wątpię, że wdrożenie adblocka potrwa tydzień. Gdyby sprawa była łatwa i prosta to adblock już dawno byłby zintegrowany z Tomato.

No tak ale co ze stronami po HTTPS? Przecież kończenie połaczenia to szyfrowanie end-to-end. Po drodze pakietu nie widać co w nim siedzi.

Jak dobrze rozumie nie będzie wersji v134 na MIPSELe tylko odrazu v135 z poprawną obsługą modemów 3G