Forum: Edimax BR-6524n

Kod Pobierz kod źródłowy


=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.03.02 14:57:36 =~=~=~=~=~=~=~=~=~=~=~=





U-Boot 1.1.3 (May  8 2008 - 15:51:24)





Board: RT2880 DRAM:  16 MB





 twe0 set to 





 toe0 set to 



flash_protect ON: from 0xBC400000 to 0xBC42B30B



protect on 0



protect on 1



protect on 2



flash_protect ON: from 0xBC430000 to 0xBC43FFFF



protect on 3



*** Warning - bad CRC, using default environment









============================================ 



ASIC -VerB/C (MAC to Phy Mode)



DRAM COMPONENT=64Mbits 



DRAM BUS=32BIT 



Total memory = 16Mbytes



Date:May  8 2008  Time:15:51:24



============================================ 



 D-CACHE set to 4 way 



 I-CACHE set to 4 way 





 ##### The CPU freq = 266 MHZ #### 





 SDRAM bus set to 32 bit 



 SDRAM size =16 Mbytes





Please choose the operation: 



   0: Load ucos code to SDRAM via TFTP Client. 



   1: Load system code to SDRAM via TFTP. 



   2: Load system code then write to Flash via TFTP. 



   3: Boot system code via Flash (default).



   4: Entr boot command line interface.



   5: Load ucos code to SDRAM via TFTP. 



 1  0 



   



3: System Boot system code via Flash.



## Booting image at bc450000 ...



Bad Magic Number,43535953 



   Image Name:   Linux Kernel Image



   Created:      2009-02-06   8:52:18 UTC



System Control Status = 0x02110084 



   Image Type:   MIPS Linux Kernel Image (lzma compressed)



   Data Size:    3514284 Bytes =  3.4 MB



   Load Address: 8a000000



   Entry Point:  881e6040



   Verifying Checksum ... OK



   Uncompressing Kernel Image ... OK



No initrd



## Transferring control to Linux (at address 881e6040) ...



## Giving linux memsize in MB, 16





Starting kernel ...







THIS IS ASIC

ramsize = 16 MBytes

rambase not set, set to default (0x08000000)

MEMORY DESCRIPTOR dump:

[0,8826b690]: base<08000000> size<01000000> type





 The CPU feqenuce set to 266 MHz



CPU revision is: 0001906c



icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0



dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0



i waysize = 4096, d waysize = 4096, i sets= 256, d sets=256



Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.



Primary data cache 16kB, 4-way, linesize 16 bytes.



[setup_scache]:1032



Linux version 2.4.30 (root@localhost.localdomain) (gcc version 3.3.6) #351 äşR1; 2ćś^ 6 16:52:13 CST 2009



Determined physical RAM map:



 memory: 01000000 @ 08000000 (usable)



On node 0 totalpages: 36864



zone(0): 36864 pages.



zone(1): 0 pages.



zone(2): 0 pages.



Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4



cause = c0808340, status = 1000fc00



calculating r4koff... 00144b50(1330000)



CPU frequency 133.00 MHz



Using 133.000 MHz high precision timer.



Calibrating delay loop... 265.42 BogoMIPS



Memory: 12308k/16384k available (1928k kernel code, 4076k reserved, 104k data, 84k init, 0k highmem)



Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)



Inode cache hash table entries: 16384 (order: 5, 131072 bytes)



Mount cache hash table entries: 512 (order: 0, 4096 bytes)



Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)



Page-cache hash table entries: 65536 (order: 6, 262144 bytes)



Checking for 'wait' instruction...  unavailable.



POSIX conformance testing by UNIFIX



Linux NET4.0 for Linux 2.4



Based upon Swansea University Computer Society NET3.039



Initializing RT netlink socket



Starting kswapd



devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)



devfs: boot_options: 0x1



squashfs: version 3.0 (2006/03/15) Phillip Lougher



pty: 256 Unix98 ptys configured



LED & GPIO & LAN Status Driver LED_VERSION 



spidrv_major = 217



Serial driver version 5.05c (2001-07-08) with no serial options enabled



ttyS00 at 0x300500 (irq = 9) is a 16550A



ttyS01 at 0x300c00 (irq = 8) is a 16550A



HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096



N_HDLC line discipline registered.



RA2880 Ethernet Driver Initilization. v1.01  256 rx/tx descriptors allocated!



Netlink init ok!



PROC INIT OK!



ICPLUS 175C config LAN_WAN finished (evaluation board)



rdm_major = 254



PPP generic driver version 2.4.2



PPP Deflate Compression module registered



PPP BSD Compression module registered



MPPE/MPPC encryption/compression module registered



FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB



physmap flash device: 800000 at 1c400000



 Amd/Fujitsu Extended Query Table v1.1 at 0x0040



number of CFI chips: 1



cfi_cmdset_0002: Disabling fast programming due to code brokenness.



Using physmap partition definition



Creating 7 MTD partitions on "RT2880 SOC Physically mapped flash":



0x00000000-0x00030000 : "Bootloader"



mtd: Giving out device 0 to Bootloader



0x00030000-0x00040000 : "Config "



mtd: Giving out device 1 to Config 



0x00040000-0x00050000 : "Factory"



mtd: Giving out device 2 to Factory



0x00050000-0x00110000 : "Kernel"



mtd: Giving out device 3 to Kernel



0x00110000-0x003e0000 : "RootFS"



mtd: Giving out device 4 to RootFS



0x003e0000-0x00400000 : "Cimage"



mtd: Giving out device 5 to Cimage



0x00050000-0x003e0000 : "Uimage"



mtd: Giving out device 6 to Uimage



Initializing Cryptographic API



IPv6 v0.8 for NET4.0



IPv6 over IPv4 tunneling driver



NET4: Linux TCP/IP 1.0 for NET4.0



IP Protocols: ICMP, UDP, TCP, IGMP



IP: routing cache hash table of 1024 buckets, 8Kbytes



TCP: Hash tables configured (established 16384 bind 32768)



IPv4 over IPv4 tunneling driver



GRE over IPv4 tunneling driver



Linux IP multicast router 0.06 plus PIM-SM



ip_conntrack version 2.1 (1152 buckets, 9216 max) - 344 bytes per conntrack



ip_conntrack_rtsp v0.01 loading



ip_nat_rtsp v0.01 loading



ip_tables: (C) 2000-2002 Netfilter core team, Type=Restricted Cone



ipt_time loading



ipt_random match loaded



netfilter PSD loaded - (c) astaro AG



ipt_recent v0.3.1: Stephen Frost .  http://snowman.net/projects/ipt_recent/



ipt_IPV4OPTSSTRIP loaded



arp_tables: (C) 2002 David S. Miller



NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.



ip6_tables: (C) 2000-2002 Netfilter core team



NET4: Ethernet Bridge 008 for NET4.0



802.1Q VLAN Support v1.8 Ben Greear 



All bugs added by David S. Miller 



Load RT2880 Timer Module(Wdg/Soft)



VFS: Mounted root (squashfs filesystem) readonly.



Mounted devfs on /dev



Freeing prom memory: 0kb freed



Freeing unused kernel memory: 84k freed



console started



trying to start /sbin/init



Algorithmics/MIPS FPU Emulator v1.5



insmod: /lib/modules/2.4.30: No such fil

Please press Enter to activate this console. Sat Jan  1 00:00:00 UTC 2000

mount: Mounting /proc on /proc failed: Device or resource busy

killall: pptp.sh: no process killed

killall: pppoe.sh: no process killed

SIOCSIFADDR: No such device

IC-Plus PHY Init...ok



GDMA1_FWD_CFG = 10000



DSP_EN OFF version driver





phy_tx_ring = 08a62000, tx_ring = a8a62000, size: 16 bytes





phy_rx_ring = 08a61000, rx_ring = a8a61000, size: 16 bytes



ra2880stop()...Done



Free TX/RX Ring Memory!



IC-Plus PHY Init...ok



GDMA1_FWD_CFG = 10000



DSP_EN OFF version driver





phy_tx_ring = 08ae6000, tx_ring = a8ae6000, size: 16 bytes





phy_rx_ring = 08a5d000, rx_ring = a8a5d000, size: 16 bytes



eth2.1: Setting MAC address to  00 1f 1f 72 c2 4c.



VLAN (eth2.1):  Underlying device (eth2) has same MAC, not checking promiscious mode.



eth2.2: Setting MAC address to  00 1f 1f 72 c2 4d.



device eth2 entered promiscuous mode



VLAN (eth2.2):  Setting underlying device (eth2) to promiscious mode.



Initialize WLAN interface

Using /bin/rt2860ap.o

2860 version : v1.6.0.0 (2007/10/12)







=== pAd = c0105000, size = 465192 ===





<-- RTMPAllocAdapterBlock, Status=0



RX DESC a8d7c000  size = 2048



<-- RTMPAllocDMAMemory, Status=0



1. Phy Mode = 9



2. Phy Mode = 9



3. Phy Mode = 9



MCS Set = ff ff 00 00 01



Main bssid = 00:1f:1f:72:c2:4c



The UUID Hex string is:2880288028801880a880001f1f72c24c



The UUID ASCII string is:28802880-2880-1880-a880-001f1f72c24c!



<==== RTMPInitialize, Status=0



0x1300 = 00064300



Setup BRIDGE interface

SIOCGIFFLAGS: No such device

SIOCGIFFLAGS: No such device

SIOCGIFFLAGS: No such device

SIOCGIFFLAGS: No such device

SIOCGIFFLAGS: No such device

bridge br0 doesn't exist; can't delete it

Setup bridge...

device eth2.1 entered promiscuous mode



eth2.1: dev_set_promiscuity(master, 1)



SIOCDELRT: No such process

device ra0 entered promiscuous mode



ra0: attempt to add interface with same source address.



SIOCDELRT: No such process

br0: port 2(ra0) entering learning state



br0: port 1(eth2.1) entering learning state



br0: port 2(ra0) entering forwarding state



br0: topology change detected, propagating



br0: port 1(eth2.1) entering forwarding state



br0: topology change detected, propagating



SIOCDELRT: No such process

SIOCDELRT: No such process

------> 802.1x--------->Enter

------> 802.1x------>Exit

Static DHCP Leases disable!

SIOCDELRT: No such process

udhcpd (v0.9.9-pre) started

Setup WAN interface

device eth2 is not a slave of br0

device eth2.1 is already a member of a bridge; can't enslave it to bridge br0.

Set: phy[29].reg[23] = 07c2

Set: phy[29].reg[22] = 8420

Set: phy[29].reg[24] = 0001

Set: phy[29].reg[25] = 0001

Set: phy[29].reg[26] = 0001

Set: phy[29].reg[27] = 0001

Set: phy[29].reg[28] = 0002

Set: phy[30].reg[9] = 1089

Set: phy[30].reg[1] = 2f00

Set: phy[30].reg[2] = 0030

Set: phy[0].reg[0] = 3100

Set: phy[1].reg[0] = 3100

Set: phy[2].reg[0] = 3100

Set: phy[3].reg[0] = 3100

********** run Diagd **********

don't create flash.inc

********** run GaTest **********

=================Enable WSC_UPNP===================

=================Enable WSC_UPNP===================

don't create flash.inc

udhcp client (v0.9.9-pre) started

=================Enable LLTD===================

killall: lld2d: no process killed

killall: snmpd: no process killed

=================END LLTD===================

=================Enable GPIO Interrupt================

into eth2.2.deconfig

killall: gpio: no process killed

ralink_gpio:ioctl GPIO REG



gPassiveMsgQ Init success! gPassiveMsgID=0x386d438f!

gActiveMsgQ Init success!

=================END GPIO Interrupt===================

sock=5!(0x0x7fff7d00)

rm: cannot remove `/tmp/agentenabledflag': No such file or directory

/bin/init.sh: 632: /bin/agent: not found

Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!

Create netlink socket thread success!

Create ioctl socket(6) success!

ip_table: set wan_name=eth2.2



killall: watchdog.sh: no process killed

@@@@@@ SSDP_PORT = 1900

killall: radiusd: no process killed

RADIUS server disable !!

cat: /var/run/webs.pid: No such file or directory

kill: 737: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or

kill -l [exitstatus]

UPnP Initialized

     IP-Addr: 192.168.2.1 Port: 49152

    HW-Addr: 00:1f:1f:72:c2:4c!

Specifying the webserver root directory -- /etc/xml

UUID Str=uuid:28802880-2880-1880-a880-001f1f72c24c!

alloc memory size=1044!





  

    1

    0

  

  

    urn:schemas-wifialliance-org:device:WFADevice:1

    11N_Router

    .

    .

    AP WSC device

    Wireless Router

    .

    .

    12345678

uuid:28802880-2880-1880-a880-001f1f72c24c

    

      

        urn:schemas-wifialliance-org:service:WFAWLANConfig:1

        urn:wifialliance-org:serviceId:WFAWLANConfig1

        WFAWLANConfigSCPD.xml

        control

        event